Important - cecotec BOLERO AGUAZERO 8000 FULL BUILT-IN Manual De Instrucciones

ENGLISH
Step 2: Water supply hose connection
Fig. 4
- Connect the water supply hose to a cold water tap, and make sure it is securely in place.
WARNING: use the water supply hose provided with your dishwasher, do not reuse the
water supply hose from your old dishwasher.
WARNING: open the tap and let water run through the water supply hose before
connecting it to the dishwasher.
WARNING: connect the water supply hose directly to the water inlet. The pressure
supplied by the inlet must be at least 0.04 MPa and at most 1 MPa. If the pressure is
over 1 MPa, you must install a pressure release valve to the inlet.
After connecting the water supply hose, open the tap completely and check if there is
any water leakage. Close the water supply tap after every washing programme.
Step 3: Draining hose connection
Fig. 5 A
1. Back of the dishwasher
2. Main cable
3. Water inlet
4. Drain outlet
5. Drain hose
6. Worktop
- Connect the water drain hose to the drain outlet in the dishwasher. Next, connect the
drain hose directly to a drain (b) or to an outlet with at least a 4-mm diameter (a). This
connection must be at least 50 cm and at most 100 cm over the floor level.
- If the end of the drain hose is free, you should not be immersed in water, to avoid water
backflow.
- Make sure the drain hose is not twisted.
IMPORTANT: utensils will not be washed correctly if you use a drain hose with over 4-m
length.
Step 4: Electric connection
- Connect the dishwasher to the electric circuit.
WARNING: make sure that the mains voltage matches the voltage stated on the rating
label of the appliance and that the wall outlet is grounded.
74
The dishwasher plug must be connected to a grounded socket. If you do not have
a grounded socket, a grounded installation must be carried out by a licensed
electrician. In case of ungrounded use, Cecotec shall not be liable for any
malfunction or damage that this may cause.
- Make sure there is an appropriate grounded socket before using the appliance.
Step 5: Placing the dishwasher
- Make sure the moisture barrier tape is almost touching the edge of the worktop.
- You must leave at least 5 mm space between the upper part of the dishwasher and the
cabinet, and the exterior door must be aligned with the piece of furniture.
- The dishwasher must be placed near the water and drain hose, previously connected, and
the power supply.
- You must ensure enough space to open the door completely.
- Note: depending on where the power supply is, you may need to drill a hole on the opposite
side of the cabinet.
- IMPORTANT: place the moisture barrier tape provided under the piece of furniture to
prevent the accumulation of condensation.
- Fix the mounting brackets (17) in the upper part of the dishwasher to ensure the correct
positioning of the fixing (5 B).
Velcro assembly
- Separate the Velcro strip A and the Velcro strip B and fix the Velcro strip A to the interior
side of the decorative panel.
- Place the felt Velcro strip B in the exterior door of the dishwasher. Fig. 6
Front panel assembly
Fig. 7
- Place the plate (14) in the decorative panel and fix it with the screws (11). In the upper part
of the decorative panel, fix a plug (18) with a screw (13) in each hole.
- Place the decorative panel in the exterior door slot of the dishwasher.
- Once the decorative panel is placed, fix it to the exterior door of the dishwasher with
screws and bolts.
1. Remove the 4 short screws. (15)
2. Set the 4 long screws (12)
Step 6: Levelling the dishwasher
1. Set the level from front to back.
2. Set the level from side to side.
- For a correct operation, the dishwasher must be level.
- Once you have placed the device, you can modify its height with the adjustment of the
ENGLISH
75
AGUAZERO 8000 FULL BUILT-IN