Hilti NURON SB 4-22 Manual De Instrucciones página 24

▶ When ripping always use a fence or straight edge guide. This improves the accuracy of the cut and
reduces the chance of the blade binding.
▶ Do not reach underneath the workpiece. The guard cannot protect you from the saw blade protruding
below the workpiece.
▶ Never hold the workpiece with your hand or other part of the body. Secure the workpiece in a sturdy
holder. It is important to secure the workpiece firmly in order to minimize the risk of body contact, blade
binding, and loss of control.
▶ Always hold the product firmly with both hands on the grips provided for the purpose and position your
arms to absorb kickback forces.
▶ Keep the grips dry, clean and free from oil and grease.
▶ Position yourself off to one side of the blade, never bring the blade into line with your body. The saw can
jump backward toward you if kickback occurs!
▶ Make sure you have a firm stance, especially for overhead work. A sudden break-through can affect your
balance.
▶ When undertaking break-through work, secure the zone on both sides of the workpiece. Pieces of debris
can fall and cause injuries.
▶ If the saw blade binds or when you interrupt work for any reason, switch off the saw and hold it motionless
in the material until the saw blade comes to a complete stop. Never attempt to remove the saw from the
workpiece or pull the saw back while the blade is in motion, as otherwise the saw could kick back.
▶ When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are
not in engagement with the workpiece.
▶ Use extra caution when sawing into walls or other blind areas. As it enters the material the blade might
encounter a hidden obstruction, resulting in kickback.
▶ Before starting the cut, check that the bandsaw blade is correctly installed. An incorrectly installed
bandsaw blade can bind and cause a kickback.
▶ Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High
vibration during long periods of work can lead to disorders of the blood vessels and nervous system in
the fingers, hands and wrists.
▶ Do not look directly into the light source (LED) of the product and do not aim the beam at other persons'
faces. Risk of dazzling or eye damage.
▶ Do not attempt to secure a belt hook in the installation opening for accessories. Use only the belt hook
supplied.
▶ Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed
accessories are secure.
Electrical safety
▶ Before beginning work, check the working area for concealed electric cables or gas and water pipes.
External metal parts of the product could give you an electric shock or cause an explosion if you
accidentally damage an electric cable or a gas or water pipe.
▶ When cutting through pipes, e.g. when carrying out demolition or installation work, check to ensure that
the pipes no longer contain liquids and empty them if necessary. When cutting through pipes, hold the
product above the level of the pipe you are cutting through. The product is not protected against ingress
of moisture.
Careful handling and use of electric tools
▶ Use only bandsaw blades of the specified size.
▶ Do not use dull or damaged bandsaw blades. They cause higher friction, binding or kickback of the
bandsaw blade.
▶ Comply with the manufacturer's instructions for handling and storing bandsaw blades.
2.4 Battery use and care
▶ Comply with the following safety instructions for the safe handling and use of Li-ion batteries.
Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
▶ Use only batteries that are in perfect working order.
▶ Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely
harmful to health!
▶ Do not under any circumstances modify or tamper with batteries!
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C
(176 °F).
▶ Never use or charge a battery that has suffered an impact or been damaged in any other way. Check
your batteries regularly for signs of damage.
18 English 2289590
*2289590*