Tabla de contenido
Publicidad
• For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
• Never use reducors or adaptors to it large-hole grinding/
cutting discs
• Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
• Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
BEFORE USE
• Before using the tool for the irst time, it is recommended
to receive practical information
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
(tools with a rating of 230V or 240V can also be
connected to a 220V supply)
• Always mount auxiliary handle E 2 and protective guard
F 2; never use the tool without them
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance
(contact with electric lines can lead to ire or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classiied as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Be careful when cutting grooves, especially in supporting
walls (slots in supporting walls are subject to country-
speciic regulations; these regulations are to be observed
under all circumstances)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Do not clamp the tool in a vice
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
• Inrush currents cause short-time voltage drops; under
unfavourable power supply conditions, other equipment
may be afected (if the system impedance of the power
supply is lower than 0,25 Ohm, disturbances are unlikely
to occur); if you need further clariication, you may
contact your local power supply authority
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualiied person
• In case of electrical or mechanical malfunction,
immediately switch of the tool and disconnect the plug
• In case of current interruption or when the plug is
accidentally pulled out, unlock the on/of switch H 2
immediately in order to prevent uncontrolled restarting
AFTER USE
• After switching of the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut of the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Mounting of accessories 2
! disconnect the plug
- clean spindle A and all parts to be mounted
- tighten clamping lange B with spanner C while
pushing spindle-lock button D
! push spindle-lock button D only when spindle A
is at a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! always mount backing pad when using sanding
accessories
! never use a grinding/cutting disc without the
label ("blotter") which is glued onto it
• Mounting of auxiliary handle E 6
! disconnect the plug
• Removing/mounting of protective guard F 7
! disconnect the plug
! ensure that the closed side of the protective
guard always points to the operator
- if necessary, adjust protective guard F by tightening
screw X which is pre-set at manufacturing (ensure
that the protective guard is closed)
• Before using the tool
- ensure that accessory is correctly mounted and irmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
• On/of locking switch H 8
- switch on tool 8a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece,
the tool should run at full speed
- lock switch 8b
- unlock switch/switch of tool 8c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
• Grinding 9
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
9
Publicidad
Tabla de contenido
