Maintenance / Service; Declaration Of Conformity - Skil 0755 Manual Original

MAINTeNANCe / serVICe

• This tool is not intended for professional use
• Opening the housing shell can damage or destroy
the tool
• Keep tool, charger and cutting blades clean
! unplug charger from power source before
cleaning
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- after use, always carefully clean and lightly lubricate
the cutting blades
! wear gloves when handling or cleaning the
cutting blades
• Regularly check the condition of the cutting blades and
the tightness of the blade bolts
• Regularly check for worn or damaged components and
have them repaired/replaced when necessary
• Sharpening the cutting blades
- remove cutting blades from tool before sharpening
- sharpen the cutting blades with a small and smooth
file, in case a solid object damaged them
- we advise you, however, to have the blades sharpened
by a specialist
- lubricate the cutting blades after sharpening
• Storage (
- store the tool indoors in a dry and locked-up place,
out of reach of children
- securely mount storage rail L on the wall with 4 screws
(not supplied) and horizontally leveled
- use blade guards M 2 when storing the tool
- lubricate the cutting blades before storing the tool
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
- in case of a defective charger send both charger and
battery to your dealer or the SKIL service station
TroUBlesHooTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
★ Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/off switch defective -> contact dealer/service
station
★ Motor runs but blades remain stationary
- internal fault -> contact dealer/service station
★ Cutting blades hot
- cutting blades blunt -> have blades sharpened
- cutting blades have dents -> have blades inspected
- too much friction due to lack of lubricant -> lubricate
blades
All manuals and user guides at all-guides.com
eNVIroNMeNT
• Do not dispose of electric tools, batteries,
• Removing/disposing of batteries )

deClArATIoN oF CoNForMITY

• We declare under our sole responsibility that the product
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
NoIse/VIBrATIoN
• Measured in accordance with EN 60745 the sound
• Measured in accordance with 2000/14/EC (EN/ISO
• The vibration emission level has been measured in
10
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ! will remind you of this when the need for
disposing occurs
! remove the battery before disposal of the tool
! only remove the batteries if they are completely
empty
- protect battery terminals with heavy tape to prevent
short-circuit
- dispose of the battery at an official collection point for
batteries
! batteries may explode when disposed of in fire,
so do not burn battery for any reason
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60335, EN 60745, EN 61000, EN 55014 in accordance
with the provisions of the directives 2006/95/EC,
2004/108/EC, 2006/42/EC, 2000/14/EC, 2011/65/EU
4825 BD Breda, NL
20.02.2014
pressure level of this tool is 56 dB(A) and the sound
power level 76 dB(A) (standard deviation: 3 dB), and the
vibration <2.5 m/s² (hand-arm method; uncertainty K =
1.5 m/s²)
3744) the guaranteed sound power level LWA is lower
than 79 dB(A) (conformity assessment procedure
according to Annex V)
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
11