Black and Decker HD555 Manual De Instrucciones página 30

16 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
FEATURES (Fig. A)
1. Slider switch
2. Cable
3. Tool free guard
4. Body grip
5. Side handle (2 positions)
6. Spindle lock button
ADDITIONAL SAFETY INSTRUCTIONS
FOR SMALL ANGLE GRINDERS
f Use the guard and ensure it is fitted correctly.
f Check mounting flanges and the disc are correctly
fitted and are undamaged.
f Ensure you are using the correct size and type of disc
for the task.
f Ensure the disc, wire brush and sanding accessories
are rated in excess of the spindle rpm of your angle
grinder. Allow a newly assembled wheel to idle off-
load for 30 seconds before starting any operation.
OPERATION
Operatingyour angle grinder (Fig. A)
To switch on, push the slider switch forward (1). To switch
off, press the rear of the slider switch.
Fittingthe discs (Fig. B and C)
Proceed as follows:
f Disconnect the plug from the electricity supply.
f Ensure the guard is fitted. Place the inner flange (7)
on the spindle. Ensure it is located on the two flats.
f Place the abrasive disc on the spindle and inner
flange (8). Ensure it is correctly located.
f Fit the threaded outer flange (9), making sure it is
facing in the correct direction for the type of disc fitted.
For grinding discs, the flange (9) is fitted with the
raised portion facing towards the disc. For cutting
discs, the flange (9) is fitted with the inner portion
facing away from the disc.
f Hold the spanner on the flats of the spindle to prevent
rotation of the disc and tighten the outer flange with
the spanner provided.
f Press in the spindle lock button and rotate the spindle
Construction
until it locks (Fig. C). Keeping the lock button pressed
Earthing
in, tighten the outer flange with the spanner provided.
Terminal
Safety Alert
Fitting sanding discs (fig. D)
Symbol
f Use a sanding disc with the backing pad for sanding
Revolutions
or Recipro-
with your angle grinder.
cation per
minute
f Disconnect the plug from the electricity supply.
f Remove the guard.
f Place the flange on the spindle. Place the backing
pad on the spindle and inner flange, ensuring it is
correctly located.
f Mount the fibre backed abrasive disc on the backing pad.