Product Familiarisation - Silverline 317338 Traducción Del Manual Original

317338
e) Select, maintain and replace the consumable/inserted tool as recommended in the
instruction handbook, to prevent an unnecessary increase in dust or fumes.
f) Use respiratory protection in accordance with employer's instructions and as required by
occupational health and safety regulations.
Specific Safety
Additional Safety Instructions for Pneumatic Devices
Air under pressure can cause severe injury:
• Always shut off air supply, drain hose of air pressure and disconnect device from air supply when
not in use, before changing accessories or when making repairs
• Never direct air at yourself or anyone else
• Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fittings
• Whenever universal twist couplings (claw couplings) are used, lock pins should be installed and
whip check safety cables should be used to safeguard against possible hose-to-tool or hose-to-
hose connection failure
• Do not exceed the maximum air pressure stated on the device
• Never carry an air tool by the hose

Product Familiarisation

1. Air Inlet Hose
2. Rubber Stop
3. Male EU Quick Connector
4. Female EU Quick Connector
5. Rubber Protector
6. Air Outlet Hose
7. Sleeve Anchor Bolt (M8 x 40mm, 10mm OD)
8. Bracket Securing Clip
9. Bracket Release Button
10. Wall/Ceiling Mounting Bracket
11. Bracket Fixing Hole
12. Hose Reel Housing
13. Reel Tensioning Axle
14. Securing Clip Release
15. Spring Tension Safety Pin
Intended Use
Garage or workshop retractable 9m air hose reel with multi-position mounting bracket for fixing to
wall or ceiling. For use with compatible air tools.
Unpacking Your Product
• Carefully unpack and inspect your product. Fully familiarise yourself with all its features and
functions
• Ensure all parts of the product are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this product
Before Use
WARNING: Always disconnect the hose from the compressed air supply before carrying out any
maintenance or repair work on this device.
WARNING: Release the spring tension before disassembling the Hose Reel Housing (12).
WARNING: DO NOT remove any safety device fitted to this device.
Assembly
Mounting the bracket:
• The Mounting Bracket (10) can be ceiling or wall mounted (Fig. I)
1. Remove the Reel Housing (12) from the Bracket by lifting the Securing Clip Release (14) and
sliding the Bracket Securing Clips (8) (Fig. II). Then press the Bracket Release Buttons (9) and
slide the Bracket off the Hose Reel Housing (Fig. III)
2. Select whether the Bracket is to be wall or ceiling mounted
3. Position the Bracket where it is to be mounted
4. Using the Fixing Holes (11) as a template (Fig. IV), use a pencil or marking chalk (not supplied) to
mark the hole positions for the Sleeve Anchor Bolts (7)
5. Remove the Bracket from the mounting position and drill the 2 x 10mm holes using a 10mm
drill bit (not supplied), to a minimum depth of 40mm (Fig. V)
WARNING: Always use a detector to check for hidden power cables or pipework before drilling.
Note: When drilling, ensure that the correct type of drill bit is used for the material being drilled.
6. Insert the Sleeve Anchor Bolts into the holes (Fig. VI)
Note: The Bolts may require tapping into the hole using a hammer (not supplied). Do not increase
the diameter of the hole to incorporate the Bolts.
7. Unscrew and remove the Bolt and washers from the inserted Sleeve (Fig. VII)
8. Position the Bracket and attach to the wall or ceiling using the Sleeve Anchor Bolts
9. Attach the Hose Reel Housing to the Bracket in reverse order to removal and ensure the Securing
Clips (8) are in the locked position (Fig. VIII)
Adjusting the hose length
• The Rubber Stop (2) should only be adjusted moving inwards towards the Reel Housing and
should not be moved outwards towards the end of the Outlet Hose (6) (Fig. IX)
• For each metre the Rubber Stop is moved inwards, the spring tension must be reduced by one
full rotation (see 'Adjusting the spring tension)
• To reduce the length of the Outlet Hose, adjust the Rubber Stop then cut the Hose to the required
length
• Ensure the length of the Hose outwards of the Rubber Stop is between 0.1-1.99m
(Fig. X)
Operation
Extending the Hose
• Pull out the Hose to the required length and slowly retract to lock it in position (Fig. XI)
Retracting the Hose
WARNING: DO NOT let go of the Hose while it is being retracted as this may cause personal
injury and damage the Hose Reel.
• To retract the Hose, pull the Hose to unlatch the locking mechanism then allow the Hose to
retract into the Housing (Fig. XII)
Accessories
• A full range of accessories including air hose connectors is available from your Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
silverlinetools.com
Air Hose Reel
7