Assembly; Operation; Important - Scheppach HMS1070 Traducción De Las Instrucciones Originales

Removing sawdust and chippings from the machine
when running is strictly prohibited.
Switch off the machine immediately it is jams. Pull out
the mains plug and remove the jammed workpiece.
Set the smallest cutting size after use to prevent the
risk of injury.
m CAUTION!
The machine must be secured to the floor / counter-
top using suitable screws / screw clamps since oth-
erwise there is a risk that it will tip over.
• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
m WARNING! Before cleaning~, adjustment~,
maintenance~ or repair work, disconnect the pow-
er cord from the main power supply!
• Check at regular intervals that the knife (24) is firm-
ly attached in the knife block.
• The knives (24) must not project more than a maxi-
mum of 1.1 mm out of the knife block.
• Make sure that the anti-kick claws (25) work cor-
rectly.
• Always wear eye protection.
• Never cut concavities, tenons or shapes.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the planing knife to run free-
ly.

8. Assembly

8.1 Parallel stop (Fig. 2)
• Now unscrew the Allen screws (17/18) coun-
ter-clockwise using the Allen key (14).
• Now attach the parallel stop (5) to the machine
housing and fasten it using the Allen screws
(17/18).
8.2 Crank handle for thickness planer chip depth
(Fig. 3)
• The crank handle (10) will be only plugged on the
spindle (19)
8.3 Chip extractor - surface planing (Fig. 4-6)
• Set the planing knife cover cpl. (13) in the upperst
position.
• Use the crank handle (10) to place the Thickness-
ing table (21) in the lowest position.
• Take the chip extractor (4) and hold the switching
pins (3) beside. Place the chip extractor (4) at a
slightly slanting angle on the machine and push it
backwards. For this you need to hold the switching
pins (3) outwards.
32 | GB
• Now lock the chip extractor (4) with the switching
pins in the table. Attention! The machine won´t
start if the switching pins are incorrectly plugged
in.
• Screw in the screw (32) from the other side of the
machine to secure the chip extractor (4).
• Now you can fold the planing knife cover cpl. (13)
down again.
8.4 Chip extractor - thickness planing (Fig. 11)
• The parallel stop (5) needs to be removed for thick-
ness planing. Follow point 8.1 in reverse order.
• Now slide the planing knife cover (7) beside so that
the cutter block is completely uncovered.
• Hold the switching pins (3) outside and set the chip
extractor (4) on top of the machine.
• Now lock the chip extractor (4) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins (3) are incorrectly plugged in.
• Screw the screw (32) into the feed table (12) to fix
the chip extractor (4).

9. Operation

m IMPORTANT!: The surfacing and thicknessing
plane has been specially designed for planing solid
wood. High alloy knives (24) are used for this pur-
pose. The contact surface of the workpiece must be
flat for thicknessing. If you want to work on large or
heavy workpieces, the machine must be secured in
place (e.g. using the thread in the machine base).
• The ON/OFF switch (1) is on the left-hand side of
the machine. Press the green key "I" to switch on
the machine. Press the red key "0" to switch off the
machine.
• The machine is fitted with an overload switch (2)
to protect the motor. In the event of an overload,
the machine will cut out automatically. After a short
time, the overload switch (2) can be reset again.
• To work on long workpieces, use roller tables or
a similar supporting arrangement. Such optional
units are available from your local DIY stores. They
must be placed at the entry and exit ends of the
plane. Their height must be adjusted such that the
workpiece is horizontal when it is fed into and out
of the machine.
9.1 Surfacing
m IMPORTANT!: Pull out the power plug before
performing any maintenance, cleaning and adjusting
work.
9.1.1 Adjustment (Fig. 7/8)
• Turn the adjustment knob for cutting depth (11) to
set the height of the feed table (12). The set cutting
depth can be read off the scale (A).
www.scheppach.com