Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Cut out dimensions (without spacers)
Without spacers
⁄
"
1
2
(1.27 cm)
With 1 or 2 spacers
⁄
"
1
2
(1.27 cm)
1 spacer
11
⁄
"
27
6 4
(29cm)
A. Bottom of cabinet cutout
2
Complete cabinet preparation following the instructions
for your type of venting. Determine venting cutout loca-
tions and cut out vent openings in the cabinets, walls and/
or soffit.
Venting outside through the roof
1
Measure and mark the lines as shown. Use a saber saw
or keyhole saw to cut an opening through the top of the
cabinet and the roof for the vent.
Cutout Chart
Cabinet Height
Hole Shape and Size
13
⁄
" (33.5 cm)
A 8
⁄
" wide x 6¼" deep (21 cm x 15.9 cm)
3
17
1 6
6 4
rectangular opening in the cabinet top is
required for damper transition clearance.
8
⁄
"
3
4
(1.9 cm)
10
⁄
"
15
1 6
(27.8cm)
⁄
19
"
34
6 4
(87.1 cm)
⁄
"
3
4
(1.9 cm)
2 spacers
11
⁄
"
59
6 4
(30.3cm)
⁄
19
34
"
6 4
(87.1 cm)
A. Cutout
B. 8
⁄
" (21 cm) x 6
17
64
C. 7
51
⁄
" (20 cm) centerline to cabinet front
64
D. Centerline of the cabinet
E. 4
⁄
" (10.6 cm)
2
5
F. 3
⁄
" (8.3 cm) center to cabinet front
17
64
G. Ø (4 cm)*
Cabinet Height
Hole Shape and Size
15" (38.1 cm)
A 6
⁄
" (15.9 cm) diameter round
1
4
opening is required.
A. Cutout
B. Ø 6¼" (15.9 cm)*
C. 7
⁄
" (19.8 cm) centerline to cabinet front
51
64
D. Centerline of the cabinet
E. 4
2
⁄
" (10.6 cm)
5
F. 3
17
⁄
" (8.3 cm) center to cabinet front
64
G. Ø (4 cm)*
2
Install the 6" (15.2 cm) air transition to the top of the
range hood liner (if removed for shipping) using two 3.5
x 9.5 mm round head screws. Assemble the vent duct
that you will use over the 6" (15.2 cm) vent transition. Use
caulking to seal the exterior wall or roof opening.
Venting outside through the wall
1
Measure from the bottom of the range hood liner to the
horizontal centerline of the vent opening (A).
B
A
C
D
2
Remove the vent duct from the range hood liner. Transfer
measurement A to the cabinet back wall. Measure from
the underside of the cabinet.
3
Mark the cutout as shown. Use a saber saw or keyhole saw
to cut a round opening through the back of the cabinet
and the exterior wall for the vent.
⁄
" (15.9 cm)*
1
4
A. Measurement A
B. Horizontal centerline of vent opening
C. Range hood liner
D. 12" (30.5 cm) min. cabinet height
Publicidad
Tabla de contenido
