Health O Meter 499KL Manual Del Usuario página 211

CALIBRATION
This scale has been factory calibrated, and does not require calibration prior to
use. If required, the scale can be calibrated. Calibration of your scale is performed
using kilograms (KG) or pounds (LB), according to the units of measure used upon
entering into the calibration path. When calibrating in pounds, a total of 300 lbs is
required (models with date codes listed below require 500 lb), applied in increments of
100 lb and 200 lb. If calibrating in kilograms, a total of 120 kg is required (or 200 kg for
models with date codes listed below), applied in increments of 40 kg, and 80 kg. THE
499KG CAN ONLY BE CALIBRATED IN KILOGRAMS.
Note: Only weights certified and traceable to national standards are to be used for
calibration procedures.
*For scales with these date codes 500 lb (200kg) of weights are required for
calibration: 3813, 4213, 1014, 2614, 2714, 3114, 3914, 4214, 4514, 0315, 1015, 1415,
1515, 1715, 2815, 3115, 3715, 4715, 5015, 5215, 0916, 2616, 3216, 4316, 4816, 0217,
1217
With the scale off, press and hold the LB/KG button (499KL) or the
blank blue button (499KG) and ZERO buttons at the same time, then
press the ON/OFF button to turn on the scale. Release all three
buttons when "CAL" appears on the display. Numbers will appear
indicating that you can begin calibration.
When calibration numbers stabilize, press the ZERO button. "C-100"
(for LB mode) or "C-40" (for KG mode) will flash on the display,
followed by "0" or "1".
Place 100 lbs or 40 kg on the scale. Numbers will appear on the
display. When calibration numbers stabilize, press the ZERO button.
"C-200" (for LB mode) or "C-80" (for KG mode) will appear on the
display, followed by "0" or "1".
Place an additional 100 lbs or 40 kg on the scale, for a total of 200
lbs or 80 kg. Numbers will appear on the display. When calibration
numbers stabilize, press the ZERO button. "C-300" (for LB mode) or
"C-120" (for KG mode) will appear on the display, followed by "0" or
"1".
Place an additional 100 lbs or 40 kg on the scale, for a total of 300
lbs or 120 kg. Numbers will appear on the display. When calibration
numbers stabilize, press the ZERO button. Calibration procedure is
now complete and "END" will appear on the display. For models with
date codes listed above the display will show "C-500" (for LB mode)
or "C-200" (for KG mode) will appear on the display, followed by "0"
or "1".
Place an additional 200 lbs or 80 kg on the scale, for a total of 500
lbs or 200 kg. Numbers will appear on the displaly. When calibration
numbers stabilize, press the ZERO button. "END" will appear on the
display, followed by "OFF". The scale will automatically shut off.
UM499KL 20190430
ACTION
211
Back to Home Page
DISPLAY
SHOWS
"CAL" followed by
numbers
Numbers followed
by "C-100" or
"C-40" then "0" or
"1"
Numbers followed
by "C-200" or
"C-80" then "0" or
"1"
Numbers followed
by "C-300" or
"C-120" then "0"
or "1"
"END"
umbers
or n
followed by "C-
500" or "C-200"
then "0" or "1"
"XXXX" followed
by "END" then
"OFF"