Creative OUTLIER FREE PRO Guia De Inicio Rapido página 3

LED Indicators
Low Battery
Charging
Fully Charged
1 2
Bluetooth Pairing /
Multipoint Connectivity
Bluetooth Connection
Established
Transferring Audio Files
1. Power off the headphones to prepare for data transfer
2. Connect the magnetic charging cable to the
headphones' magnetic charging port, then, connect the
other end to an available USB-A port on your PC or Mac
3. Outlier Free Pro will be detected as a mass storage
device on your PC or Mac. Drag and drop the audio files
onto the mass storage device to begin data transfer
4. Once the data transfer is complete, safely eject the mass
storage device from your PC or Mac
Important: Do not disconnect the USB cable while data
transfer is in progress. Disconnecting the USB cable without
safely ejecting the mass storage device may result in loss of
data or damage to the built-in memory.
Charging Outlier Free Pro
Ensure that the magnetic charging cable is securely
connected to the headphones' magnetic charging port
before connecting it to a power source to charge. If the
magnetic charging cable is not secured or if it is connected
incorrectly, remove the cable, and reconnect it to the
headphones. It is essential for the headphones to be
connected securely and properly to the charging cable to
prevent short circuit when there is an active current.
Master Reset
To initiate a Master Reset, enter Bluetooth pairing mode,
then press and hold the Volume + and Volume - buttons
for 5s. Upon completion, Outlier Free Pro will play a voice
prompt of "Power Off" before powering off.
Master Reset is reserved for cases where users encounter
issues while headphones are in use or during situations
such as: Bluetooth pairing failure, random LED blinking, or
to reset all data.
Blinks red every 3s
Solid red
Solid blue
Alternate red and blue
Blinks blue once every 5s
when audio is playing
Blinks blue twice every 5s
when no audio is playing
5s
Preparing To Go Swimming / Underwater
Attach the provided microphone plug as illustrated to
properly secure Outlier Free Pro's microphone from water
or moisture. Ensure that the plug is firmly sealed before
going swimming or underwater to prevent potential water
damage. If any amount of water has entered through the
microphone, immediately remove the headphones and
shake off excess water from the microphone.
If you would like to reduce the length of the microphone
plug, cut away the excess as shown.
Disclaimer: The microphone plug must be attached before
entering the swimming pool or any body of water; the
plug should not be attached when you are already in the
water. The Outlier Free Pro supports up to a depth of 1.5m
for up to 40 minutes at a time. Creative shall not be liable
for any water damage if water is found in the microphone
or is found to have entered through the microphone if the
microphone plug is not used or not properly fitted.
Tip: To hear better while swimming, put on the provided
silicone earplugs to block out underwater noise and to enjoy
a more immersive audio playback experience.
Technical Specifications
Headphone Drivers: Bone Conduction Transducers
Frequency Response: 20–20,000 Hz
Microphones: Omni-directional x 1
Bluetooth Version: Bluetooth 5.3
Bluetooth Profiles
• A2DP (Advanced Audio Distribution Profile)
• AVRCP (Audio / Video Remote Control Profile)
• HFP (Hands-free Profile)
Audio Codec: SBC
Operating Frequency: 2402–2480 Hz
Operating Range: Up to 10m / 33 ft
Voice Assistant Support: Siri and Google Assistant
Built-in Memory Capacity: 8 GB
Supported Music Formats: MP3, FLAC, WAV, APE
Playtime: Up to 10 Hours*
Charging Time: 2 Hours
Charging Interface: USB-A (Charging and Data Transfer)
Battery Type: Rechargeable Lithium-ion Polymer Battery
180 mAh 0.666 Wh
Input: 5V 1A
Operating Temperature: 0–45°C
Maximum RF Output Power: 4 dBm
IP Rating: IPX8**
*Based on moderate volume level. Actual battery life will vary
with use, settings, songs, and environmental conditions
**Protected against submersion in freshwater up to a depth
of 1.5m for up to 40 minutes. IPX8 rating does not include
submersion in salt water or liquids with similar properties