Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
4a. Short press the CH knob (5) again to
in the MENU. The parameter stops flashing and, if the function has
more than one parameter, the following parameter flashes...
4b. Long press (1s) the CH knob (5) again to
exit
in the MENU.
disappears from the display.
5. If no key is pressed, the unit
appears from the display.
Note: The UP/DN buttons (13) on the microphone have the same
effect as the rotary CH knob (5). The PTT switch (12)
without validating.
disappears from the display.
1) COLOR
Press the CH knob (5) for 3 seconds to
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
select
the COLOR menu.
2. Press the CH knob (5) to confirm. The color flashes in the display.
3. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
change
the color.
4a. Short press the CH knob (5) again to
in the MENU.
4b. Long press (1s) the CH knob (5) again to
exit
in the MENU.
disappears from the display.
5. If no key is pressed, the unit
appears from the display.
Color default is orange :
2) DIMMER
DIMMER function allows adjusting the brightness of the lighting. 10
steps from 0 to 9.
Press the CH knob (5) for 3 seconds to
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
select
the DIMMER menu.
2. Press the CH knob (5) to confirm. The dimmer value flashes in the
display.
validate
your choice and
validate
your choice and
exits
MENU after 10 seconds.
exits
enter
MENU.
appears.
validate
the color and
validate
the color and
exits
MENU after 10 seconds.
enter
MENU.
appears.
stay
3. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
change
4a. Short press the CH knob (5) again to
stay
in the MENU.
and
4b. Long press (1s) the CH knob (5) again to
value and
exit
in the MENU.
dis-
5. If no key is pressed, the unit
appears from the display.
Dimmer default value is : 5.
MENU
3) CONTRAST
CONTRAST function allows adjusting the contrast of the display.
10 steps from 0 to 9.
Press the CH knob (5) for 3 seconds to
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
select
microphone to
2. Press the CH knob (5) to confirm. The contrast value flashes in the
display.
3. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
change
4a. Short press the CH knob (5) again to
stay
in the MENU.
and
stay
4b. Long press (1s) the CH knob (5) again to
value and
exit
in the MENU.
5. If no key is pressed, the unit
appears from the display.
dis-
Contrast default value is : 5.
4) KEY BEEP
Beep on changing the channel, keys etc...
Press the CH knob (5) for 3 seconds to
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
select
2. Press the CH knob (5) to confirm. The status of the function flashes
in the display.
3. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
activate
microphone to
47
the value of the dimmer.
validate
the selected value
validate
disappears from the display.
exits
MENU after 10 seconds.
enter
MENU.
the CONTRAST menu.
the value of the contrast.
validate
the selected value
validate
disappears from the display.
exits
MENU after 10 seconds.
enter
MENU.
the KEY BEEP menu.
deactivate
on /
of the function.
the selected
dis-
appears.
the selected
dis-
appears.
Publicidad
Tabla de contenido
