Publicidad
Idiomas disponibles
Idiomas disponibles
safety precautions and usage statements
Power Ratings:
INPUT:
AC 100–240V 50/60 HZ 2.0A
OUTPUT:
DC 29V 2.0A
WATTS:
58W
Product Ratings:
The lift motors are not designed to operate continuously for more than two
[2] minutes in an eighteen [18] minute time period or approximately 10% duty
cycle. Attempting to circumvent or exceed this rating will shorten the life
expectancy of the product and may void the warranty.
The massage motors are not designed to operate continuously for more
that 30 minutes at a time. Please allow the massaging system to rest for 30
minutes after automatic massage shut off before restarting.
Weight Limits:
The recommended weight limits on theTEMPUR ERGO
BY SLEEPTRACKER-AI
are: Twin Long / Full / Queen / King / Split CA King /
®
CA King: 750 pounds.
Maximum weight the bed can support per person is 275 pounds with the
weight evenly distributed across the head and foot sections. This product
is not designed to support or lift this amount of weight in the head or foot
sections alone.
NOTE: Exceeding the recommended weight restrictions could damage your
TEMPUR ERGO
SMART POWERED BY SLEEPTRACKER-AI
®
warranty. For best performance, you should enter and exit the TEMPUR
ERGO
SMART POWERED BY SLEEPTRACKER-AI
®
fully lowered position.
TEMPUR ERGO
SMART POWERED BY SLEEPTRACKER-AI
®
bed frames, furniture beds and platform beds that are certified to hold a
minimum of 900 pounds. If using this adjustable base without the legs and
placing directly on a bed frame or platform bed, cross-bed supports (slats)
are strongly recommended to ensure TEMPUR ERGO
SLEEPTRACKER-AI
maintains stability during operation.
®
Exceeding this weight restriction could damage the bed
and/or cause injury and will void the warranty.
Acoustics:
In normal base operation the wheels, which allow the bed to maintain its
distance from the wall, will make contact with the steel platform supports of
2
the base creating a contact noise. When entering, exiting or shifting weight
on the base, this contact noise may be audible as the wheels make contact.
This is normal.
Fabric Care:
To prolong the life of your fabric, protect from direct sunlight whenever
possible. For spot cleaning, wipe area with a light damp sponge or vacuum
with a soft brush attachment to remove particles. Keep at a minimum of
30cm (12 inches) away from direct heat sources.
For deeper cleaning, blot liquid spills with a clean dry cloth. Wipe with a clean
cloth dampened with warm water. Do not wet excessively. A soft bristle brush
may be used to remove ingrained soil. Avoid scratching by gentle brushing.
Wipe with a clean cloth dampened with warm water to remove residues after
brushing. Dry in shade away from direct heat.
SMART POWERED
®
If persistent marks remain visible after cleaning, seek professional advice.
FCC Compliance:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
and void your
®
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
while it is in the flat or
®
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
fits easily inside
®
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
SMART POWERED BY
®
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
• Consult the dealer or an experienced radio/TV technician for
CAN ICES-3 (B)/NMB-3(B)
that to which the receiver is connected.
help.
Publicidad
