Publicidad
Idiomas disponibles
Idiomas disponibles
Note: Using a pan or pot that's not suitable for induction cook-
ing may damage the appliance.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent
and rinse with clean water.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
• Special care must be taken when moving or transporting the
machine due to its heavy weight. With at least 2 persons or
using a cart. Move the machine slowly, carefully, and never
incline more than 45°.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems
Possible cause
The appliance does
Electrical power
not switch ON.
connection is not
connected properly
with the electrical
outlet.
Cooling fan is
This is normal. The
operating even
cooling fan con-
after the appliance
tinues running in
is switched to
Standby mode for
Standby mode.
some time to cool
down all internal
elements.
The green LED
Without cooking
flashes once and
utensil on the
switch off for 2
stove top or using
seconds
an inappropriate
cooking utensil.
The red LED flash-
- The device heats
es twice and switch
up extensively.
off for 2 seconds
- Parts are dam-
aged
The red LED
Stove-top overheat
flashes three times
and switch off for 2
seconds
The red LED
Voltage un-
flashes four times
der-loaded/
and switch off for 2
over-loaded
seconds
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
ranty, state where and when it was purchased and include proof
of purchase (e.g. receipt).
In line with our policy of continuous product development we
reserve the right to change the product, packaging and docu-
mentation specifications without notice.
GB
Possible solution
Check the electri-
cal power connec-
tion to make sure
it is connected
properly.
Wait until the
cooling fan stops
rotating.
Place or replace a
suitable pan with
a flatted bottomed
on the plate.
- Clear the ventila-
tion slots and let
the device cool
off for several
minutes. If the
error code has
shown when the
appliance is in
cooling condi-
tion, contact the
supplier.
- Contact the
supplier.
Make sure water is
inside the pan.
Make sure the volt-
age and frequency
comply with the
rating label shown
on the product.
11
Publicidad
