Stiga A 1500 Manual De Instrucciones página 12

the operating mode of the robot lawn mower and to force
it to return to the charging base.
• "CONFIRM" push button (Fig. 1.G): it is used to confirm
the set operating mode.
• "SCHEDULED PROGRAMME" luminous icon (Fig. 1.l):
it is used to display the scheduled programme settings.
• "SINGLE WORK CYCLE" luminous icon (Fig. 1.L): it is used
to display the settings of the single work cycle.
• "RETURN TO BASE" luminous icon (Fig. 1.H): it is used to
display the settings of the forced return of the robot lawn
mower to the charging base.
• "BLUETOOTH" push button (Fig. 1.M): it is used to display
the blue tooth status.
• "ALARM" luminous icon (Fig. 1.N): it is used to display
alarm statuses.
• "BATTERY" luminous icon (Fig. 1.O): it is used to display
the battery charge level.
NOTE: For a more detailed description of the commands
listed above, please refer to the Smart User Manual.
3.3. CHARGING BASE OPERATION
The charging base is equipped with a warning light (Fig. 7.N)
which lights up as shown below:
• Warning light off: the charging base is powered off or the
robot is on the base.
• Fixed warning light: the robot lawn mower is not connected
to the charging base and the antenna signal is correctly
transmitted.
• Flashing light: the charging base is not set up correctly,
or a charging base fault has been detected.
3.4. BATTERY CHARGING
The "BATTERY CHARGING" procedure allows to recharge
the robot lawn mower manually.
1. Position the robot lawn mower on the charging base
(Fig. 8.R).
2. Slide the robot lawn mower onto the charging base, until
the charging connector is engaged (Fig. 8.S).
3. Press the "STOP" push button (Fig. 8.A) to open the
cover (Fig. 8.B) and access the control panel (Fig. 8.C).
4. Turn the robot lawn mower on with the "ON/OFF" button
(Fig. 8.E).
5. The "BATTERY" luminous icon (Fig. 8.O) flashes blue,
the robot lawn mower is charging.
6. Close the cover (Fig. 8.B).
7. Leave the robot lawn mower to charge for at least the
time shown in Par. 2.3.3.
NOTE: Charging the battery before winter storage should
be carried out as illustrated in Par. 4.3.
3.5. CUTTING HEIGHT ADJUSTMENT
Follow APP wizard to adjust the cutting height.
CAUTION:
Do not touch the cutting means when adjusting
the cutting height.
NOTE: The length of the grass cut by the robot lawn
mower must not exceed 10 mm.
EN
4. MAINTENANCE
CAUTION:
Only use original spare parts.
CAUTION:
Do not modify, tamper with, elude or eliminate
the safety devices installed.
CAUTION:
Danger of cutting hands.
Use protective gloves to avoid cutting your
hands.
CAUTION:
Danger of dust in the eyes.
Use safety glasses to avoid the danger of
dust in the eyes.
WARNING:
Too much water can filter in and damage
electrical parts.
BAN:
Do not use pressurized water jets.
BAN:
To avoid irreversible damage to the electrical
and electronic components, do not immerse
the robot lawn mower, partially or completely,
in water.
BAN:
Do not wash the internal parts of the robot
lawn mower to avoid damaging the electrical
and electronic components.
BAN:
Do not use solvents or petrol so as not to
damage varnished surfaces and plastic parts.
4.1. SCHEDULED MAINTENANCE
For a better operation and longer life, be sure to clean the
product regularly and replace worn parts.
Perform the interventions following the frequency indicated
in the table.
FREQUENCY COMPONENT
Weekly Blade
Recharging con-
tacts
Monthly Robot lawn mower Carry out cleaning. (See
Charging base and
power cables
5
TYPE OF
INTERVENTION
Clean and check blade
efficiency (See Par. 4.2)
If the blade is bent due
to impact or if it's worn,
replace it. (See Par. 4.2)
Clean and eliminate any
oxidising. (See Smart User
Manual)
Smart User Manual)
Check for wear or dete-
rioration and replace if
necessary. (See Smart
User Manual)