Stiga A 1500 Manual De Instrucciones página 14

PROBLEM
The robot lawn mower does not
position itself properly inside the
charging station.
The charging base light does not
turn on when the robot is out of the
charging base.
The charging base light is flashing.
The warning icon is on on the
keyboard
The robot lawn mower stops
temporarily in the work area.
7. TECHNICAL DATA
SPECIFICATIONS
Dimensions (WxHxD)
Weight of the robot lawn mower
Cutting height (Min-Max)
Blade diameter
Cutting speed
Speed of movement
Maximum slope
Maximum slope along the perimeter
Type of cutting system
Cutting device code
Sound power level detected
Uncertainty of noise emissions, KWA
Sound power level guaranteed
Acoustic level audible by the operator
IP rating of the robot lawn mower
IP rating of the charging station
IP rating of the power supply
Robot lawn mower operating ambient
temperature [° C]
Charging station operating ambient
temperature [° C]
Power supply ambient operating
temperature [° C]
Work capacity
Power supply
Battery model
Charging time
CAUSES
Problem with the charging base antenna.
Ground next to the charging base has collapsed Restore the correct positioning of the charging base.
The charging base has not been calibrated
correctly, or electromagnetic interferences may
be present in the vicinity of the base.
The supply voltage is missing or there is a fault
in the charging base.
There is a fault in the charging base.
The charging base is not set up correctly.
It indicates anomaly / failure conditions.
Weak GPS signal
STIGA A 1500
413 x 252 x 560 [mm]
8.5 [kg]
20-60 [mm]
180 [mm]
2850+/-50 [rpm]
22 [m/min]
45%
20%
4 pivoting cutting blades
322104105/0
57 [dB] (A)
1.47 [dB] (A)
59 [dB] (A)
46.3 [dB] (A)
IPX5
IPX1
IP67
0°C-50°C
-10°C-50°C
-10°C-50°C
1500 [m ]
2
Input: 100-240vac 1.2 A
Output: 30Vcc 2A
25.2 V-5Ah
150 [min]
EN
SOLUTIONS
If the problem persists, contact a service centre.
(See Par. 2.3.1).
After eliminating the source of disturbance, calibrate the
charging base using the app. Please refer to the Smart
User Manual.
Check that the power supply unit is plugged in correctly.
Check the integrity of the power supply connection cable.
Turn off the charging base and turn it on again after a few
minutes. If the problem persists, contact a service centre.
Set up the charging base using the app. Please refer to the
Smart User Manual.
For more information consult the app or refer to the Smart
User Manual
If the problem persists, contact a service centre
STIGA A 3000
529 x 299 x 695 [mm]
12.5 [kg]
20-65 [mm]
260 [mm]
2400+/-50 [rpm]
24 [m/min]
50%
20%
6 pivoting cutting blades
322104105/0
56 [dB] (A)
0.56 [dB] (A)
57 [dB] (A)
45.2 [dB] (A)
IPX5
IPX1
IP67
0°C-50°C
-10°C-50°C
-10°C-50°C
3000 [m
2]
Input: 100-240vac 1.2 A
Output: 30Vcc 2A
25.2 V-5Ah
150 [min]
7
STIGA A 5000
529 x 299 x 695 [mm]
13 [kg]
20-65 [mm]
260 [mm]
2400+/-50 [rpm]
24 [m/min]
50%
20%
6 pivoting cutting blades
322104105/0
56 [dB] (A)
0.56 [dB] (A)
57 [dB] (A)
45.2 [dB] (A)
IPX5
IPX1
IP67
0°C-50°C
-10°C-50°C
-10°C-50°C
5000 [m
2]
Input: 100-240vac 0.65 A
Output: 30Vcc 4A
25.2V – 2x 5Ah
150 [min]