Makita AC001G Manual De Instrucciones página 11

Pressure switch:
The pressure switch automatically starts the motor
when the air tank pressure drops to the factory set
cut-in pressure. It stops the motor when the air tank
pressure reaches the factory set cut-out pressure.
Safety valve:
If the pressure switch does not shut off the air compres-
sor at its cut-out pressure setting, the safety valve
will protect against high pressure by popping out at
its factory set pressure which is slightly higher than the
pressure switch cut-out setting.
Outlet pressure gauge:
The outlet pressure gauge indicates the air pressure
available at the outlet side of the regulator. This pres-
s u r e i s c o n t r o l l e d b y t h e r e g u l a t o r a n d i s a l w a y s l e s s o r
equal to the tank pressure.
Tank pressure gauge:
The tank pressure gauge indicates the air pressure in
t h e t a n k .
Regulator:
The air pressure coming from the air tank is controlled
b y t h e r e g u l a t o r k n o b . T u r n t h e k n o b c l o c k w i s e t o
increase pressure and counter-clockwise to decrease
pressure. To avoid minor re-adjustment after making
a change in pressure setting, always approach the
desired pressure from a lower pressure. When reducing
from a higher to a lower setting, first reduce to some
pressure less than desired pressure. Depending on the
air requirements of each particular accessory, the outlet
regulated air pressure may have to be adjusted while
you are operating the accessory.
Air outlet:
For regular pressure pneumatic tool, use outlet max
pressure; 0. MPa ( . bar).
When using a quick coupler in the market, install it to
t h e a i r o u t l e t u s i n g t h e t w o w r e n c h e s a s s h o w n i n t h e
figure.
Fig.4: 1. A i r o u t l e t 2. uick coupler 3. W r e n c h
NOTE: If the quick coupler does not have any air
sealing method, we recommend applying an ade-
quate measure such as a sealing tape.
Daily Start-up Checklist
WARNING:
Do not use the power tool if the
s itch does not turn it on and o . Any power tool
t h a t c a n n o t b e c o n t r o l l e d w i t h t h e s w i t c h i s d a n g e r o u s
and must be repaired.
Connecting hoses
WARNING:
Risk of Unsafe Operation
Firmly grasp hose in hand when installing
to prevent hose whip. Losing control of the
hose may result in personal injury and prop-
erty damage.
Always follow all safety rules recommended
by the manufacturer of hoses, connectors,
air tools, and accessories in addition to
all safety rules for the air compressor.
Following this rule will reduce the risk of
serious personal injury.
1. Before attaching air hose or accessories, make
sure On/Auto-Off switch lever is set to Off , the battery
is removed, and the air regulator or shut-off valve is
c l o s e d .
2. Attach hose and accessories. Too much air pres-
sure causes a hazardous risk of bursting. Check the
manufacturer's maximum pressure rating for air tools
and accessories. The regulator outlet pressure must
never exceed the maximum pressure rating.
NOTICE:
Air pressures above 0.7 MPa (7 bar)
is recommended. The delivery hoses should be
fitted ith a safety cord such as ire rope.
3.
I n s t a l l t h e b a t t e r y c a r t r i d g e a n d t u r n t h e O n / A u t o -
Off switch to On/Auto and allow tank pressure to build.
Motor will stop when tank pressure reaches cut-out
pressure.
4. Open the regulator by turning it clockwise. Adjust
the regulator to the correct pressure setting. Your com-
pressor is ready for use.
5.
Always operate the air compressor in well-venti-
lated areas; free of gasoline or other solvent vapors. Do
not operate the compressor near the spray area.
When you are finished:
Disconnecting hoses
WARNING:
Firmly grasp hose in hand when disconnect-
ing to prevent hose whip. Losing control of
the hose may result in personal injury and
property damage.
Air tanks contain high pressure air. Keep
face and other body parts away from out-
let of drain. Always wear approved safety
glasses with side shields when draining as
debris can be kicked up into face.
1. Set the On/Auto - Off switch to Off and remove
t h e b a t t e r y c a r t r i d g e .
2. T u r n t h e r e g u l a t o r c o u n t e r c l o c k w i s e t o s e t t h e
outlet pressure to zero.
3. R e m o v e t h e a i r t o o l o r a c c e s s o r y .
4.
Open the drain valve located at the lower part of
the air tank. Tank pressure should be below 0.14 MPa
( 1. 4 b a r ) w h e n d r a i n t h e a i r t a n k .
5. T i l t t h e t a n k s o t h a t t h e d r a i n v a l v e i s d i r e c t l y
b e l o w a n d d r a i n .
WARNING:
T i l t t a n k t o d r a i n .
WARNING:
valve slowly and tilt compressor to empty accu-
mulated water. Keep face and eyes away from the
drain valve.
WARNING:
IN THE AIR TANK. IF NOT DRAINED, W ATER
W ILL CORRODE AND W EAKEN THE AIR TANK
CAUSING A RISK OF AIR TANK RUPTURE.
11 ENGLISH
Risk of Unsafe Operation
Risk of bursting
To drain tank, open the drain
W ATER W ILL CONDENSE