Vaporesso 200 Manual De Instrucciones página 6

9.Lock or unlock the device
Press the fire button 3 times, then the +, - and mode buttons will be locked. In the same
way, the buttons will be unlocked and the screen will be unlocked.
10. Choose a Mode
1. Long press the mode button for main mode selection ( Pulse Mode/F(t) Mode/VWN Mode).
2. Press the mode button 3 times continuously for secondary menu setting.
*F(t): F(t) MODE (DEFAULT)
F(t) MODE is by adjusting temperature, heating speed and time, F(t) mode releases the
flavors of e-liquid adequately, delivering the perfect balanced tasting experience consistently
from the first puff throughout.
*PUL: PULSE MODE
PULSE MODE is a mode to improve vaping experience through constant voltage output,
delivering optimal flavor production, throat hit, nicotine satisfaction, and perfect temperature
cloud continuously.
*VWN: VARIABLE WATTAGE MODE/ SIMPLE MODE
VWN MODE is a normal mode of output wattage, you can according to the coil resistance to
adjust the best wattage for your needs. The user interface shows wattage, resistance and
puff counter for your immersive vaping experience.
*DIY: DIY MODE
You can choose traditional VW (H, N, S), VV, BP (Bypass) modes in this section.
*SET: SYSTEM SET
System setting includes DEFAULT, SMART VW, PUFF, and VERSION options.
SMART VW: when this function is turned on and a TANK is installed, the system will
recommend the best power.
PROTECTIONS
1. Short circuit protection & Low resistance protection:
When the load resistance is less than 0.05 Ω, press the ignition key devise will enter the
short circuit protection and close the output, screen will display "SHORT ATOMIZER".
2. Low resistance protection:
When the load resistance is less than 0.09 Ω, press the ignition key devise will enter the Low
resistance protection and close the output, screen will display "LOW RESISTANCE".
3. No load protection:
When no load resistance is detected, press power button could trigger the no load
protection, the device will close the output, at the same time OLED display will show "CHECK
ATOMIZER".
4. High resistance protection:
When the load resistance is greater than 5Ω, press power button could trigger the high
resistance protection, the device will close the output, at the same time OLED display will
show " CHECK ATOMIZER ".
5. Low voltage protection:
When the voltage of the battery cell is lower than 3.3V, press power button could trigger the
low voltage protection, the device will close the output, at the same time OLED display will
show "LOW BATTERY".
6. PCBA(Printed Circuit Board Assembly):
When the temperature of PCBA sensor reaches 60-85 degrees, screen display "OVER HEAT"
and output is closed.
7. Over discharge protection:
In the discharge process, when the voltage between PCBA power supply welding spot B+ and
B- is less than 2.9v, the output is automatically closed.
8. USB High Voltage Input Protection:
Switching in the charger, stop charging when the input voltage to USB port exceeds 6V and
is lower than 30V.
9. Over charge protection:
During the charging, the battery voltage will rises to 4.2V+/-0.3V,the screen will display "100%"
10. Auto-shut off protection
When POWER button is held for 10±1 seconds, the device will close the output, at the same
time OLED display will show "OVER TIME".
CAUTIONS
1. Please turn off the device when it is not in use.
2. Do not leave the charging device unattended.
3. Do not drop, throw or abuse your device, which may cause damage.
4. Please use a standard USB output charger with proper charging current and voltage range.
5. Keep away from the water or any flammable gas, liquid .
6. Keep away from corrosive chemicals.
7. Do not expose the device to direct sunlight, dust, moisture or mechanical shock.
8. Do not expose the device to extreme temperature. (Recommended temperature range:
-10~45 ℃ /14~113 ℉ while using and -10~45 ℃ /14~113 ℉ while storing).
9. EEE Recycling: The product should not be treated as household waste, instead, it should
be handed over to the applicable collection point for the recycling of electrical and electronic
equipment.
3 ENGLISH