Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY INSTRUCTIONS FOR PRUNING SHEARS
The tool is not to be used by children. The tool is not intended for use by people with impaired physical or mental abilities, or by
people without experience in or understanding of the operation of the equipment, unless they will be supervised or instructed to
use the product safely, in a manner ensuring that the risks involved are understood. Children should not play with the product.
Children should not be allowed to perform cleaning and maintenance of the equipment without supervision.
Do not expose the tool to rain or other precipitation. It is also forbidden to expose the charger and the battery to rain or other
precipitation.
The tool is not intended for use in explosive atmospheres or high humidity conditions, especially in steam condensation conditions.
Pay special attention during operation – falling branches may pose a threat to the operator and bystanders. Keep bystanders at
a safe distance from the workplace.
The pruning shears are only used for cutting wood; it is forbidden to cut other materials. Ensure that no other materials get be-
tween the blades. Be careful not to cut the wires, which may be hidden among the branches.
Warning! Ensure that the fingers of the other hand supporting the branches for cutting do not come into contact with the blades.
This can cause serious injury.
Always wear protective gloves for all works with the tool, its maintenance and adjustment.
PRODUCT OPERATION
Installing the battery (II)
Warning! Before installing the battery in the tool, make sure that the power switch is in the off position, i.e. it is not pressed down.
Slide the battery into the battery socket guides until it latches in the socket. A correctly installed battery cannot be removed other-
wise than by pressing and holding the battery latch in this position, and then pulling the battery out of the tool socket.
Operating the pruning shears
The pruning shears are turned on by pressing the power switch.
Press and hold the power switch for approx. 3 seconds to turn on the pruning shears. The blades will open (III). Press the power
switch again to cut. The blades make a full movement and then open automatically.
The pruning shears will be turned off after pressing and holding the power switch for approx. 3 seconds. The blades will close (IV).
If the pruning shears are left unattended (battery connected, but the power switch not pressed), it will enter sleep mode after about
30 seconds. The blades will close automatically.
At the top of the housing, there is a LED lamp informing about the tool status. The device also generates an audible signal. The
table below shows the combination of light and sound signals.
LED lamp status
Green steady light
Red flashing light
Turned off
Red flashing light – 3 flashes
Turned off
Red flashing light
Pruning shears operation tips
The maximum cutting diameter is given for softwood cutting (e.g. conifers, poplar, linden) in the case of hardwood cutting (e.g.
ash, walnut tree, oak) the maximum cutting diameter may be reduced.
The pruning shears are used to completely cut the branches. Do not use it for any other purpose, for example, cutting boards or
carving.
Do not cut materials other than wood. Other materials can lead to faster wear of the blades or even their damage.
Before cutting branches, make sure that there are no foreign objects, such as nails or staples, which may damage the tool.
Make sure that there are no electrical wires, water, gas and other hoses before starting work, the cutting of which will lead to their
destruction, and may pose a threat to the operator or bystanders, e.g. electric shock, gas or water leakage.
Before each press of the power switch starting the cutting, make sure that the fingers of the other hand or other parts of the body
do not come into contact with the blade. The pruning shears' blades may cause serious injury.
In the case of cutting tree branches, pay attention to the falling branches, which may pose a threat to the operator and bystanders.
Before starting work, designate a secure a zone in which bystanders may not stay. Persons working in such a zone should wear
personal protective equipment at least the same as the operator.
O R I G I N A L
14
Audible signal
1 signal
Continuous signal until the blades are opened
1 signal before the diode goes off
3 signals every 2 seconds until the tool goes into
sleep mode
2 signals
5 signals
EN
Tool status
The tool is on
The blades are jammed. The blades are opened. After the diode goes off
and the audible signal stops, you can resume operation.
The tool was inactive for 30 seconds and enters sleep mode.
The overheating protection of the tool has been activated. Before resuming
work, wait 10 – 15 minutes for the tool to cool down.
The tool is turned off
The tool has made 2,000 cuts. Check the condition of the blades.
I N S T R U C T I O N S
Publicidad
