GRAPHITE 58G011 Traducción Del Manual Original página 10

temperature outside of defined range may damage the battery and
increase the risk of fire.
CHARGER REPAIRS
• Do not repair damaged charger The charger can be repaired only by
the manufacturer or in an authorised workshop.
• When disposing of the worn out charger, take it to a service point
where you can utilize such wastes
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and additional
safety systems are used, nevertheless there is always a small risk of
injuries at work.
Li-Ion batteries may leak, set on fire or explode when heated to high
temperature or short-circuited. Do not store the batteries in a car in
hot and sunny days. Do not open the battery. Li-Ion batteries contain
electronic protection devices that, if damaged, may cause fire or
explosion of the battery.
Explanation of used symbols
1 2
5 6
9 10
Max.
50°C
Read instruction manual, observe warnings and safety
1
14
13
conditions therein.
Use protective goggles and hearing protectors.
2
Work with protective mask on.
3
Keep the tool away from children.
4
Protect against rain.
5
Use indoors, protect from water and moisture.
6
Be careful, sharp edges!
7
Use protective gloves
8
Recycling.
9
Protection class 2.
10
Segregated waste collection.
11
Do not throw cells into fire.
12
Hazardous to water environment.
13
Do not allow to heat above 50°C.
14
CONSTRUCTION AND USE
Jigsaw is a hand held battery-powered device. Drive consists of a DC
commutator motor. The tool is designed for making straight, coarse
cuts, curved cuts and holes in wood, wood-based materials, plastics
and metals (provided that appropriate blade is used).
Range of use covers repair and building works, and any work from
the range of individual, amateur activities (tinkering).
Use the tool only in accordance with its purpose
3 4
7 8
11
12
10
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Switch lock button
1
Switch
2
Adapter
3
Footplate
4
Switch for pendulum action setting
5
Blade holder
6
Guiding roller
7
Edge guide locking screws
8
Blade protection
9
Guard
10
Lighting
11
Battery lock button
12
Battery
13
Charger
14
LED diodes
15
Button for battery level indication
16
Battery level indicator (LED)
17
Edge guide
18
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Hexagonal key - 1 pce
1
Edge guide - 1 pce
2
PREPARATION FOR OPERATION
REMOVING AND INSERTING THE BATTERY
• Push the battery lock button (12) and slide out the battery (13)
(fig A).
• Insert charged battery (13) into the handle holder, you should
hear when the battery lock button (12) snaps.
BATTERY CHARGING
The device is supplied with partially charged battery. The battery
should be charged in ambient temperature between 4°C and 40°C. New
battery, or one that has not been used for a long time, will reach full
efficiency after approximately 3 to 5 charge/discharge cycles.
• Remove the battery (13) from the device (fig A).
• Connect the charger to mains socket (230 V AC).
• Slide the battery (13) into the charger (14) (fig B). Ensure the battery
is properly fitted (pushed to the end).
When the charger is connected to a mains socket (230 V AC), the
green diode (15) on the charger turns on to indicate connected
supply.
When the battery (13) is placed in the charger (14), the red diode
(15) on the charger turns on to indicate that the charging is in
progress.
At the same time green diodes (17) of the battery level indication
are flashing in different configurations, see description below.
• All diodes are flashing - battery is empty and requires charging.
• 2 diodes are flashing - the battery is partially discharged.
• 1 diode is flashing - the battery level is high.
Once the battery is charged, the diode (15) on the charger lights
green, and all battery level diodes (17) light continuously. After
some time (approx. 15 s) battery level indication diodes (17) turn
off.
Do not charge the battery for more than 8 hours. Exceeding this
time limit may cause damage to battery cells. The charger will not
turn off automatically when the battery is full. Green diode on
the charger will remain on. Battery level indication diodes turn
off after some time. Disconnect power supply before removing