Publicidad
Idiomas disponibles
Idiomas disponibles
3. Turn the froth adjustment dial (D1) to "CLEAN" (fig. 20).
"CLEANING UNDERWAY RECIPIENT UNDER SPOUT" appears
on the display (B1) together with a bar which gradually
fills as cleaning progresses. Cleaning stops automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the steam
connection nozzle (A9) with a sponge (fig. 22).
Please note!
•
To prepare a number of cappuccinos or milk-based cof-
fees, clean the milk container after you have prepared
the last beverage only. To proceed with making the next
beverages, press "
displayed.
•
If you do not clean the milk container, the
pears on the display to remind you that it needs cleaning.
•
The milk container can be kept in the refrigerator.
•
In some cases, before cleaning you must wait for the appli-
ance to heat up.
10.
DELIVERING HOT WATER
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. Press the selection arrow (B2) corresponding to the "
symbol (B3) to enter the menu;
4. Press the selection arrow (B2) corresponding to the
"NEXT>" symbol to display "HOT WATER";
5. Press the selection arrow corresponding to "HOT WATER".
The corresponding image appears on the display (B1), to-
gether with a progress bar which fills gradually as prepara-
tion proceeds;
6. The machine delivers hot water, then delivery stops auto-
matically. To interrupt hot water delivery manually, press
the selection arrow corresponding to " STOP" icon again.
22
ESC". When the "CLEAN" message is
symbol ap-
Please note!
•
If "Energy Saving" mode is active, you may have to wait a
few seconds before hot water is delivered.
•
Preparation of each coffee can be customized (see sections
"12. Customizing the beverages "and"13. Memorizing
your personal profile").
11.
STEAM DELIVERY
Important! Danger of burns.
Do not leave the appliance unattended while steam is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Press the selection arrow (B2) corresponding to the "
symbol (B3) to enter the menu;
4. Press the selection arrow (B2) corresponding to the
"NEXT>" symbol to display "STEAM";
5. Press the selection arrow corresponding to " STEAM". The
corresponding image appears on the display (B1), togeth-
er with a progress bar which fills gradually as preparation
proceeds and after a few seconds, steam to heat the liquid
is delivered from the cappuccino maker;
6. When the required temperature or froth level is obtained,
interrupt steam delivery by pressing the selection arrow
corresponding to "STOP
Important!
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
Please note!
If "Energy Saving" mode is active, you may have to wait a few
seconds before the hot water is delivered.
11.1 Tips for using steam to froth milk
•
When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
•
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 41°F/ 5°C).
"
•
For a creamier froth, rotate the container with slow move-
ments in an upward direction.
•
To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following section.
11.2 Cleaning the hot water/steam spout after
use
Always clean the hot water/steam spout (C6) after use to avoid
the build-up of milk residues and prevent it from clogging.
16
".
"
Publicidad
