Publicidad
Idiomas disponibles
Idiomas disponibles
•
To turn the appliance on, press the
9). The message "HEATING UP UNDERWAY PLEASE WAIT"
appears on the display.
•
When heating is complete, the message changes to:
"RINSING UNDERWAY, HOT WATER FROM SPOUTS". As
well as heating the boiler, this also heats the internal cir-
cuits by circulating hot water.
The appliance is at temperature when the main screen (home-
page) appears.
6. TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water flows from the brewing unit
(A8). Avoid contact with splashes of water.
•
To turn the appliance off, press the
9).
•
The message "TURNING OFF UNDERWAY, PLEASE WAIT"
is displayed, then the appliance performs a rinse cycle and
goes off (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
•
first turn the appliance off by pressing the
(fig. 9);
•
release the main switch (A21) at the back of the appliance
(fig. 2).
Important!
Never press the main switch while the appliance is on.
7.
MENU SETTINGS
7.1
Rinsing
Use this function to deliver hot water from the brewing unit (A8)
and hot water/steam spout (C6), if inserted, to clean and heat
the appliance's internal circuit.
Place a container with a minimum capacity of 3.38 floz /100ml
button (A7-fig.
under the coffee and hot water spouts (fig. 8).
To enable the function, proceed as follows:
1. Press the selection arrow (B2) corresponding to the "
2. Press the selection arrow corresponding to "
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
3. After a few seconds, hot water is delivered first from the
9
4. To interrupt rinsing, press the selection arrow correspond-
Please note!
•
•
7.2 Descaling
For instructions on descaling, see section "15.
7.3 Water filter
For instructions on how to install the filter (C4), see section"17.
Water softener filter".
7.4 Beverages settings
button (A7) (fig.
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage.
1. Press the selection arrow (B2) corresponding to the "
2. Scroll through the menu items by pressing the selection
3. The values for the first beverage appear on the display;
button
4. The reference user profile is highlighted on the display. The
5. To go back to the settings menu, press the selection arrow
6. To reset the default values for the beverage displayed,
9
symbol (B8) to enter the menu;
brewing unit, then from the hot water/steam spout (if in-
serted) to clean and heat the appliance's internal circuit.
"RINSING UNDERWAY, HOT WATER FROM SPOUTS" appears
on the display, together with a progress bar which fills
gradually as preparation proceeds;
ing to " STOP" or wait for rinsing to stop automatically.
If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
After cleaning, it is normal for the coffee grounds container
(A10) to contain water.
symbol (B8) to enter the menu;
arrow corresponding to "NEXT>" until "
SETTINGS" appears on the display;
values are displayed on vertical bars. The default value is
indicated by the
symbol, while the current value is
highlighted by the solid part of the vertical bar;
corresponding to "
ESC". To scroll through and display
the beverages, press the selection arrow corresponding to
"NEXT>";
press the selection arrow corresponding to "
"
RINSING";
Descaling".
"
BEVERAGES
RESET";
Publicidad
