Descargar Imprimir esta página

Cembre TW-18B Manual De Uso Y Mantenimiento página 11

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

FW S1K54601
LED lights (3)
The 2 LEDs make it possible to light the working area and are useful for poorly lit conditions.
They turn on automatically when the torque wrench is used and turn off approximately 10 seconds after the
motor has stopped.
11
5.1) Menu screens
TW-18B
TW-18B
01/01/2022
08:00
01/01/2022
08:00
FASTENER
SEQUENCE
JOB
200-250Nm
000000
000000
W SFSF ON
FASTENER
SEQUENCE
JOB
200-250Nm
000000
000000
W SFSF ON
01/01/2022
08:00
N
01/01/2022
08:00
K
W
01/01/2022
08:00
KS
FASTENER
SEQUENCE
JOB
200-250Nm
000000
000000
W SFSF ON
FASTENER
SEQUENCE
JOB
11
01/01/2022
200-250Nm
000000
000000
W SFSF ON
08:00
NR-25B
21AW090
Lorem ipsum
5. NAVIGATION MENU
CLICK
10
Initial screen
This shows for several seconds when the tool is switched on.
Main screen (example)
summarises the tool's main configuration parameters:
date/time and battery charge level
RUN
W: Fastening configuration
SFSF: progress along the track (for work certification only)
RUN
FASTENER
200-250Nm
ON: data recording enabled (for work certification only)
W SFSF ON
The main screen is shown each time the display turns on
FASTENER
200-250Nm
W SFSF ON
01/01/2022
Fastening type
08:00
allows the operator to select the configuration of the component to be
fastened, choosing between: W, N, K and KS. The system automatically
PUSH
W
sets the corresponding tightening torque:
W, K, KS=200-250 Nm N=150-200 Nm.
RUN
N.B: it is compulsory to set this parameter before proceeding with any
RUN
fastening.
01/01/2022
08:00
The navigation menu is shown on the display (11).
The selector knob (10) allows the user to browse the
menu, select a parameter and confirm a selection:
Turn to select a screen and to move within the
screen, the selected parameter will be highlighted
in light blue.
Press to enter the screen or to confirm a selection.
01/01/2022
08:00
01/01/2022
08:00
SEQUENCE
JOB
000000
000000
SEQUENCE
JOB
000000
000000
TURN
N
01/01/2022
08:00
K
01/01/2022
08:00
KS
UNSCREW
EN
UNSCREW
5
BAT1
BAT2
BATT. NTC
FAULT
DRIVER
A
MOTOR
FW
!
5
BAT2
BAT1
01/01/2022
08:00
01/01/2022
08:00
FASTENER
200-250Nm
W SFSF ON
FASTENER
200-250Nm
W SFSF ON
01/01/2022
08:00
01/01/2022
08:00
01/01/2022
08:00
N
K
W
KS
01/01/2022
08:00
OK
OK
SEQUENCE
JOB
000000
000000
SEQUENCE
JOB
000000
000000
PUSH
ERROR
01/01/2022
08:00
ERROR
N
W
KS
01/01/2022
08:00

Publicidad

loading

Este manual también es adecuado para:

Tw-18baTw-18be