Cembre TW-18B Manual De Uso Y Mantenimiento página 18

7.2.2) Fastening operation (with work certification)
Before starting fastening operations with certification, it is essential to carry out certain
preliminary steps in order to set up the tool correctly and enable the recording function.
Check that the USB drive is inserted into the port.
The tool makes it possible to certify work carried out (JOB) with the value of the
tightening torque for each attachment along the section in question:
Follow these instructions in order:
Press the ON/OFF button (7) to switch on the torque wrench.
TURN
Use the selector (10) to determine the parameters on the following screens:
01/01/2022
08:00
01/01/2022
N
08:00
N
W
W
KS
KS
01/01/2022
08:00
01/01/2022
SSSS 08:00
TOT: 002h24m
SSSS
FFFF
FFFF
SSFF PAR: 000h56m
SSFF
SFSF
Long push for reset
SFSF
FREE
FREE
01/01/2022
TURN
08:00
ON
01/01/2022
08:00
TOT: 000517
PAR: 000031
01/01/2022
Long push for reset
08:00
TOT: 002h24m
01/01/2022
OK
08:00
PAR: 000h00m
FASTENER SEQUENCE
200-250Nm 000000
W SFSF ON
01/01/2022
08:00
ON
01/01/2022
08:00
ERROR
PUSH
01/01/2022
08:00
Turn and press the selector (10) according to the type of configuration on
which you wish to work, choosing between codes W, N, K and KS, which will
K
be highlighted in light blue.
PUSH
K
The correct tightening torque will already be pre-set by the system.
In the case of code "K" configuration, to ensure correct torque, check
that the screw's washer is properly greased: to prevent any sticking
during the fastening.
01/01/2022
08:00
SSSS
Turn and press the selector (10) to define the operator's working advance
PUSH L
FFFF
along the track, choosing between SSSS FFFF SSFF SFSF FREE.
PUSH
SSFF
SFSF
Once the working advance has been selected, it is essential to com
FREE
ply with it in order to save the data correctly.
START
PUSH
Turn and press the selector (10) to enable the data recording function by PUSH
OFF
selecting ON.
PUSH L
01/01/2022
Proceed with the fastening as described in points 3-4-5 of § 7.2.1;
PUSH
the successful completion of the operation will be confirmed by "OK".
JOB
000000
TURN
When the work has been completed, end the recording by selecting OFF.
OFF
For the transfer of data, see § 7.3.
Contact an authorized CEMBRE service
center to carry out ordinary maintenance.
01/01/2022
08:00
01/01/2022
N
08:00
N
K
W
K
W
KS
KS
01/01/2022
08:00
TOT: 002h24m
SSSS
FFFF
PAR: 000h00m
SSFF
SFSF
FREE
START
01/01/2022
08:00
ON
01/01/2022
08:00
TOT: 000517
PAR: 000000
08:00
Turn the button to set the brightness.
Push to confirm.
JOB FUNCTION NOT AVAILABLE
The validity of the calibration
has expired.
EN
01/01/2022
08:00
TURN
01/01/2022
08:00
N
W
KS
01/01/2022
08:00
SSSS
FFFF
SSFF
SFSF
FREE
TURN
OFF
01/01/2022
08:00
PUSH
CLICK
10
1sec.
CLICK
PUSH
01/01/2022
K
01/01/2022
JOB FUNCTION NOT AVAILABLE
PUSH
The validity of the calibration
has expired.
Contact an authorized CEMBRE service
center to carry out ordinary maintenance.
01/01/2022
08:00
PUSH
18
08:00
W
K
08:00
SSSS
FFFF
SSFF
SFSF
FREE