Publicidad
Idiomas disponibles
Idiomas disponibles
TECHNICAL CHARACTERISTICS:
Voltage:
220 V~
Frequency:
60 Hz
Current:
10 A
3 450 RPM
Speed:
Motor Rated Power:
3 Hp
Maximum Motor Power:
4 Hp
Maximum Pressure:
116 PSI
Tank Capacity:
47.5 Gal
Air Flow:
7.7 CFM - 40 PSI
5.7 CFM - 90 PSI
Power Cord Grips Type: Y
All conductors are: 1.5 mm
x 3 C with 221 ºF insulating temperature
2
Insulation quality: Basic insulation.
Insulation quality: Class I
Thermal insulation of motor winding: Class B
CAUTION
To avoid risk of electrical shock or serious accident,
if power cord gets damaged it should be repaired by the manufacturer
or by Truper
Authorized Service Center
®
Power cord grips used in this product: Type"Y".
Assembly design in this product causes insulation to be affected by
liquid spills or splashing.
Before gaining access to terminals, all power
WARNING
circuits should be disconnected.
WARNING
We do not recommend using power cord
extensions with compressors. Using that type of extension
cause power drops resulting in motor potency loss and
overheating. Instead of using an extension cord increase the
compressor's action scope connecting a longer hose into the
outlet. Connect additional hose lengths as needed.
BELT DRIVE AIR COMPRESSORS.
- Do not use compressed air to clean clothes.
- Do not apply compressed air directly to skin.
- Do not apply compressed air for breathing purposes unless the air
is filtered with a filter specifically for built to that purpose.
- Do not use open-air piping. It could lash out and cause injuries.
- Do not use flammable liquids to clean the compressor.
- Do not use an open fire to inspect inside the compressor or the
pressure deposit.
- Wear eye protection when using compressed air to clean the unit.
- Use caution not to blow particles towards people: always use an air
gun for cleaning.
- Double-check all the auxiliary fixtures are functioning adequately
and have the right capacity for the application.
- Inspect regularly that all covers are fixed and firmly set.
- Replace all parts, tools and accessories when unfit for a safe operation.
- Install a check-valve or a cut valve in the inlet piping in case
compressor shall be parallel coupled with a second compressor or
if it will be connected to an air supply system.
- Double-check all piping and hoses connected to the compressor have
the right diameter, and, adequate resistance for the maximum
pressure delivered by the compressor.
- Install the compressor making available an adequate ventilation air
supply towards the unit. Use care not to restrict air ducts through
the inlets in the cover and motor fan.
4
ENGLISH
INSPECT:
Inspect the pumps' rotation direction during the initial start up. Verify
any modification in the electric components' or connections.
Turn off the compressor and disconnect from the power outlet.
Ventilate completely before disassembling any component or making
any maintenance service.
INSTALLATION AND VENTILATION
To service the compressor allow adequate access and free space up
and around the unit. It needs adequate protection against weather.
Good ventilation is essential. To gain maximum efficiency admission
air shall be as cold and clean as possible (a 37.4 ºF drop in temperature
will increase 1% the delivered air volume). Gas impurities and particles,
abrasive dust and corrosive gasses are especially harmful. The exhaust
vapors are hazardous if compressed air is used to supply breathing
devices.
Set the compressor as far away as possible from the work areas to
prevent from suctioning particles generated by the job
(paint, dust, etc.)
WARNING
This unit SHOULD BE USED with
220 V~ - 240 V~
feeding tension. Using a different
TENSION WILL SEVERELY
DAMAGE the unit.
CONNECTION TO THE MAIN POWER SUPPLY
The compressor shall be set as close as possible to the main power
supply. Double-check the power supply matches the voltage indicated
in the motor nameplate.
WARNING
This unit must be grounded.
CAUTION
The power cables are coded with
the following colors:
GREEN
GROUND
BLUE
CURRENT
BROWN
CURRENT
This tool is in compliance with
the Official Mexican Standard
(NOM - Norma Oficial Mexicana).
Publicidad
