Silverline 951855 Traducción Del Manual Original página 10

GB
Fitting a wire cup brush
1. Remove Outer Flange (16), Disc (10) (if installed) and Inner Flange (15) from the Spindle (17)
2. Screw wire cup brush directly onto Spindle
3. Depress the Spindle Lock (13) button and rotate the Spindle until you feel the Spindle Lock
engage
4. Tighten the wire cup brush with a suitable spanner. Release the Spindle Lock button. The tool is
now ready for use (Image A)
5. To remove a wire cup brush, depress the Spindle Lock button, rotate the Spindle until you feel the
lock engage, then use a suitable spanner to remove the wire cup brush
Rotating the Handle
The main handle can be rotated typically used for a vertical cut for example when cutting concrete.
1. Depress the Handle Rotation Switch (4)
2. Rotate the Main Handle (5) 90° left or right from its normal central position (Fig. II)
3. Release the Handle Rotation Switch and ensure the Main Handle is locked in position before use
Operation
Switching ON/OFF
Note: Do not switch the tool ON/OFF when the Disc (10) is in contact with the workpiece. Always
allow the motor to reach its full speed before applying load, and to stop completely before placing
the angle grinder down. Always hold the tool securely, using both hands, on the handles provided.
Note: This tool features both Lock 'ON' and Lock 'OFF' using a Trigger Lock (7)
1. Grip the Main Handle (5) and Auxiliary Handle (1) firmly
2. Push the Trigger Lock (7) forward (Fig. III, position 'a')
3. Depress and hold in position to use the ON/OFF Trigger Switch (6) to start the tool (Fig. III,
position 'b')
• To lock the Trigger Switch in the 'ON' position, press the Trigger Lock and depress the ON/OFF
Trigger (Fig. III, position 'c')
• To stop the tool, release the ON/OFF Trigger Switch. if operating with the ON/OFF Switch in the
locked position, press and release the ON/OFF Trigger Switch to switch the tool 'OFF'
Grinding
• Only use discs specifically manufactured for grinding operations. Stone and metal grinding discs
are not interchangeable, use the correct disc for your application
• When grinding, keep the tool at approximately 15 to 30° to the workpiece surface (Image B)
Note: Do not apply too much pressure to the tool while grinding. Excessive pressure does not result
in more effective removal of material, but will in fact cause premature wear of the grinding disc and
increase wear and tear on the tool.
Cutting
WARNING: Always ensure that the correct guard for use with cutting discs or superabrasive
wheels is installed.
• Only use discs specifically manufactured for cutting operations. Stone and metal cutting discs are
not interchangeable, use the correct disc for your application
• Never use cutting discs for grinding operations. The disc might shatter and produce projectiles
that could injure the operator and bystanders
• When cutting, always keep the angle of the disc constant. Do not apply any sideways force to
cutting discs, as this might lead to the disc becoming jammed in the cut and shatter
WARNING: Do not apply too much pressure to the tool whilst cutting. Excessive pressure does
not result in more effective or faster cutting, but will in fact cause premature wear of the cutting disc
and increase wear and tear on the tool.
Note: The cutting disc will wear during use, and the disc diameter will gradually reduce in size. The
smaller the disc becomes, the more strain will be placed on the motor. To avoid damage to the tool,
only use cutting discs that are no less than 75% of their original size.
Using a cup brush or wire wheel
• Always check that the no load speed of the grinder does not exceed the max speed of the cup
brush or wire wheel
• Ensure that no part of the cup brush or wire wheel can come into contact with the tool housing
• Run the grinder, with cup brush or wire wheel attached, for at least 30 seconds before use to
check that the cup brush or wire wheel is secure, and properly balanced
• When using a wire cup brush or wire wheel, avoid applying excess pressure. Using greater force
will not make the cup brush or wire wheel more effective, but will bend the wires out of shape
and damage the brush
10
Accessories
• A full range of accessories including grinding, cutting and flap discs, diamond wheels and wire
cup brushes, is available from your Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: Always remove the plug from the mains power supply before carrying out any
maintenance/cleaning.
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life
• Clean the body of your tool with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
• Do not clean with organic solvents which is harmful to the power tool body material
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• To replace the brushes;
a) remove the Brush Access Covers (8) from both sides of the tool
b) Remove the worn brushes and replace with new
c) Replace Brush Access Covers
• Alternatively, have the tool serviced at an authorised service centre
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools