Silvercrest 264219 Manual De Instrucciones página 6

EN
Intended Use
Hand-held electric paddle mixer used for the preparation of plaster, cement, levelling compounds,
emulsions and similar building and decorating materials.
The tool must ONLY be used for its intended purpose. Any use other than those mentioned in this
manual will be considered a case of misuse. The operator, and not the manufacturer, shall be liable
for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable
for any modifications made to the tool, nor for any damage resulting from such modifications.
Unpacking Your Tool
• Carefully unpack and inspect your product. Fully familiarise yourself with all its features and
functions
• Ensure all parts of the product are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this product
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Attaching a mixing paddle
WARNING: Always disconnect from the power supply before attaching/changing accessories.
WARNING: Never fit any attachment with a maximum speed lower than the no load speed
of the machine.
• This plaster mixer is equipped with an M14 female Output Drive (3)
• M14 threaded mixing paddles are fitted by screwing them into the Output Drive. Tighten with
a suitable spanner
• Ensure that the mixing paddle is securely tightened before use
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as well
as suitable gloves, when working with this tool.
Switching ON and OFF
WARNING: Always ensure that the power cord is not interfering with the mixing paddle or
presenting a tripping hazard for the operator or other personnel in the vicinity.
Note: The Switch Lock Button provides the dual function of preventing accidental operation of
the ON/OFF Trigger Switch; and also locking the ON/OFF Trigger Switch in the ON position for
continuous use.
• Grip the mixer firmly by the Handles (4), with both hands
• To start the mixer, press the Switch Lock Button (6) to release the ON/OFF Trigger Switch (5)
• Press and hold the ON/OFF Trigger Switch
• Press the Switch Lock Button to lock the tool in the 'ON' position
• To stop the mixer, squeeze the ON/OFF Trigger Switch and release
Gear selection
• The mixer is fitted with 2 gears, a higher torque lower speed gear (0-480min
higher viscosity liquids which need less rapid mixing and a higher speed gear (0-800min
lower viscosity liquids
• Select the required gear using the Gear Switch (9), (Fig. I)
Note: Never change gear while the mixer is operating.
Speed selection
• The mixer is fitted with variable speed control
• To alter the speed, simply adjust the Variable Speed Dial (8). The higher the number, the faster
the speed
Mixing of material
WARNING: ALWAYS wear adequate personal protection equipment when mixing compounds,
including safety goggles or a face shield, breathing protection (specific to the material used), gloves
(suitable for the material used), hearing protection, and a hard hat where required.
WARNING: This tool is designed for two-handed operation. Never use with one hand, or
attempt to mount stationary or prop-up against another object.
Note: ALWAYS refer to the compound manufacturers mixing requirements and recommendations.
• The shape and size of a mixing paddle that is ideal for a specific application will depend on the
type of material being mixed:
° Substances with a low viscosity such as dispersion paint, varnish,
thinset, sealing and levelling compounds, cement, grout etc., will
require a mixing paddle with a left-hand twist
° Substances with a high viscosity, such as ready-mixed plaster,
concrete, screed, putty and epoxy resin, will require a mixing paddle
with a right hand twist
• It is important to keep the paddle moving throughout the bulk of the material whilst mixing,
as opposed to keeping it in one central position in the mixing container. Mix until compound
is completely blended
6
264219_OwnerManual_SEPT.indd 6 264219_OwnerManual_SEPT.indd 6
WARNING: DO NOT overload the motor whilst mixing. When you recognise a significant drop in
speed, switch off immediately to avoid damage to the tool. Consider changing to a different mixing
paddle or accessory more suitable for the material.
WARNING: When you have completed the mixing procedure, allow the mixer to come to a
complete stop before lifting it out of the material. Make sure not to contaminate the environment
and clean-up potential spillage.
WARNING: To avoid damage to the machine and cross-contamination between different
materials, always clean the mixing paddle immediately after use. Don't let the material dry
on the accessory. Also, refer to the paragraph 'Cleaning' in the 'Maintenance' section below.
Accessories
• A range of accessories for your tool, including mixing paddles in numerous sizes and for
different compounds, is available from your Silverline stockist. Spare parts can be obtained from
toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life
• Clean the body of your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol
or strong cleaning agents
• Never use caustic agents to clean plastic parts
• Use water, a suitable cleaning solution, or mild solvent to clean rests of material off the accessory.
Wear appropriate protection equipment whilst cleaning, including eye, hand and breathing protection
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• If you suspect that the brushes may be worn, have them replaced at an authorised Silverline
service centre
Contact
) suitable for
-1
) for
-1
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
De Keten
00004
5651 GJ
Eindhoven, Netherlands
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
• ALWAYS remove all material from the accessory, clean and dry the tool before storage
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
09/09/2021 12:57 09/09/2021 12:57