SCOPREGA GEBTP-2 MiMa Manual De Instrucciones página 6

M A N U A L O F
SAVE THESE INSTRUCTIONS
2. PREMISE
Dear customer,
congratulations on choosing Scoprega.
We design and manufacture products of the highest quality according to the
needs of our customers. Scoprega also offers the highest quality in assistance.
Our dedicated offices guarantee advice and instructions in case of need, as
well as complete technical assistance.
We thank you for your trust.
ATTENTION
Read these instructions before using the inflator. Failure to follow all of the instructions
listed below could result in damage to the product and / or cause serious injury.
3. PRELIMINARY WARNINGS
1. Read these instructions.
2. Keep this manual.
3. Follow the instructions faithfully.
4. Protect the power cord from possible damage.
5. For assistance, contact only qualified personnel.
In the event of problems or damage to the inflator, it is necessary to contact assistance.
6. Do not disassemble the device. Incorrect reassembly can cause short circuits.
7. Ensure adequate ventilation and avoid placing objects on or around the inflator during
operation.
8. Do not block the air vents.
9. The inflator produces vibrations that could generate a displacement of the same. Do not place
the device on high floors and monitor its movements.
10. Do not use the inflator with adapters other than those provided in the package, they could
damage the device.
11. Keep the device out of the reach of children.
DO NOT POWER THE INFLATOR AT A HIGHER
VOLTAGE THAN NOMINAL.
4. INTRODUCTION
The GE BTP-2 MiMa represents the evolution of two inflators such as the GE BP1 and the GE BTP-1.
It is suitable for many applications but is ideal for SUP, being able to reach 1.2 bar (18 psi) of
maximum pressure. It is equipped with a special pressure gauge for selecting the desired pressure.
When it is reached, it stops automatically.
10
I N S T R U C T I O N S
5. RECOMMENDED USES
Rubber boats (max 3m), kites, SUP boards, rafts, air mattresses,
pool inflatables.
6. TECHNICAL DATA
VOLTAGE CAPACITY
ITEM
(V) (L / minute)
420 (turbine)
GE BTP-2
12 Vdc
120 (piston)
7. GENERAL SAFETY RULES
1. ALWAYS CONSIDER THE WORKING ENVIRONMENT.
Do not expose the inflator to rain. Do not use in the presence of flammable liquids or gases.
2. AVOID UNINTENTIONAL STARTINGS.
Do not start the inflator with the inlet in contact with dust or water.
3. CHECK THAT THERE ARE NO DAMAGED PARTS.
Before using the inflator make sure that the external parts are intact and that the inflator works as
described.
4. DO NOT USE
the inflator near flammable liquids or gaseous or explosive atmospheres. The
engine of this inflator produces sparks and these can ignite fumes.
5. BE CAREFUL NOT TO INHALE!
The compressed air coming from the inflator is not pure. Never inhale air from the inflator or from a
breathing device connected to the inflator.
6. ATTENTION! RISK OF EXPLOSION.
Inflate to the pressure recommended by the inflatable manufacturer. Excessive pressure can cause
a burst that is dangerous to people.
7. NEVER LEAVE THE DEVICE WITHOUT SOMEONE'S SUPERVISION.
Excessive pressure can cause a burst that is dangerous to people.
8. ATTENTION! RISK OF MALFUNCTIONING.
Do not modify or attempt to repair. Do not perforate the casing or make any changes to the inflator
or its parts.
9. ATTENTION! RISK OF FIRE.
Allow the inflator to cool down for 10 minutes after using it for up to 20 minutes. Prolonged use can
cause overheating and damage the product.
10. Never transport the pump by the hose or cable.
11. BE CAREFUL.
Care must always be taken. Use common sense.
MAX
CURRENT
PRESSURE
FUNCTIONS
CONSUMPTION
(mbar)
(A)
INFLATE /
1200 14.5
DEFLATE
11