Publicidad
Idiomas disponibles
Idiomas disponibles
Green means ready for next measurement. When 37.4℃-38.0℃, it's yellow ,means
slight fever warning. Please pay attention to body temperature. When the body
temperature is above 38.1℃, it's red , means high fever. Please take action to cool down
or go for a doctor.
2) To ensure the accuracy of the measurement, wait at least 30 seconds after 5
consecutive measurements.
Mode conversion
When the device is running, pressing the MODE button to cycle conversion between
"body" mode and "surface" mode.
"body" mode is used for measuring human body temperature, the "surface " mode is
used to measure the surface temperature. (The factory default is "body" mode).
Recalling and Erasing Memory Data
The last temperature taken before the thermometer powers off is stored in
memory, up to 50.
1) In the boot or shutdown state, short press the MEMO button to view the
history of measured values.
2) An empty memory cell shows "---℃" or "---℉".
3) Temperature readings can be stored in memory. Up to 50 temperature
readings can be stored into the memory cells and automatically overwrite
historical data.
4)In boot mode, press the MEMObutton until the LCD display "CLR", which
means that all stored data is cleared completely.
Parameter settings
This product can be set according to the subjects of different colors and different
environments data to meet the different characteristics of populations or individuals.
Long press the SET button to modify the measurement parameters
3- Troubleshooting
MESSAGE
SITUATION
Temperature taken in not within Typical
human temperature range.
(34.0~43.0℃ or 93.2℉~109.4℉).
Measured over the distance:1-5cm (0.4-2in)
Incorrect test position.
Subjects forehead hair, Antipyretic stickers,
head with sweat, etc.
Some people's body temperature is lower
than the general population.
Operating temperature exceeds the range of
speci�ied temperature.
The screen �licker, automatic turn off.
Battery capacity is too low. Taking
Temperature is not allowed.
Ambient temperature changes too fast
(1) Power is off.
(2) Improper battery installation.
(3)The battery is exhausted.
(4)Display remains blank.
SOLUTION
Make sure the forehead thermometer is
for forehead measurement, not other
human body site.
Optimum measurement distance is 1cm
See �igure 2 Measuring position and distance.
Subjects sit quietly 5-10 minutes before the
test.
The main concern fever temperature
Move to a room within the operating range
wait 30 minutes before taking temperature.
Replace battery or the product has been
damaged, needs repairs.
Install a new battery
Wait until the ambient temperature
is stably.
(1)Press ON button again.
(2)Check the battery polarity.
(3)Replace with a new battery.
(4)Contact the retailer or service center.
HTD8813 as below step:
1)Unit Set-F1
Under the boot mode .Long press SET button to enter F1, press the "MODE" or
"MEMO"button to switch Celsius and Fahrenheit temperature units, press the SET
button to con�irm the unit settings (factory default is Celsius).
2)Fever alert set-F2
Under F1 state, press SET button to enter the F2, press the "MODE" button to
decrease 0.1 ℃, press the "MEMO" button plus 0.1 ℃, long press to accelerate the
speed of temperature regulation, and �inally press the SET button to save. (The
factory default is 38.1 ℃)
3)Prompt sound settings-F3
Under F2 state , short press SET button to enter F3, press MODE button or MEMO
button to set voice switch, and press the SET button to con�irm the settings. (The
factory default is the voice Prompt to open).
Prompt sound settings ON/OFF function
Under the boot mode .Short press SET button to take on or take off the Prompt sound
function.
Restore to factory setting function
Under the boot mode, long press MODE button until LCD display "rst". Two seconds
later ,former F1-F3 parameter back to factory setting.
4-Replacing the Battery
1. Open and release battery cover following indicator on the surface of battery cover.
Before changing the battery be sure the system is already power off.
2. Remove the battery and replace with 2 new one, type AAA, Make sure align properly
as indicated inside the battery cover .
3. Slide the battery cover back in until it snaps in place.
Do not dispose of used batteries in household waste. Take them to special local
collection sites.
4. In case, if system is latched up after changing battery. You may not follow up the
process of rule one. Just take off battery, waiting 30 sec, then load battery again.
Warning
Do not recharge, disassemble or dispose of in �ire.
1.The typical service life of the new and unused batteries is 2000 measurements for
the operation time is 18s.
2. Only use the recommended batteries, do not recharge non-rechargeable batteries
and do not burn them.
3. Remove the batteries if the thermometer is not to be used for a long period.
Publicidad
