Econo Cool Operation; I-Save Operation - Mitsubishi Electric MFZ-KA25VA Manual De Instrucciones

ECONO COOL OPERATION

Use this operation when you want to be comfortable in COOL mode even with energy saved.
Perform the following operations while the unit is operat-
ing in the MANUAL COOL mode.
I
Press the
When the
conditioner performs swing operation vertically in various cycle according to
the temperature of air conditioner.
Also SET TEMPERATURE is automatically set 2°C higher than in COOL mode.
To release the ECONO COOL operation:
I
Press the
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
• When the
the ECONO COOL operation, ECONO COOL operation is released.
• The
are available.
What is "ECONO COOL"?
Swing air flow (change of air flow) makes you feel cooler than constant air flow. So, even though the set temperature is
automatically set 2°C higher, it is possible to perform cooling operation with keeping comfort. As a result, energy can be saved.
ECONO COOL
button.
(ECONO COOL) operation is selected in COOL mode, the air
ECONO COOL
button again.
button is pressed or the operation mode is changed during
TOO TOO
FAN WARM COOL
button, the or button and ON/OFF timer (explained below)

i-save OPERATION

With this function, you can save the settings such as temperature, fan speed, and air flow direction for
both cooling and heating operation.
To start i-save operation:
1
Press the
i-save operation can only be set during cooling or heating operation.
2
Press the
The operation indicator lamp on the right side of the indoor unit lights in or-
ange.
To set the temperature, fan speed, and air flow direction
for i-save operation:
1
Press the
2
Press the
3
Press the
The next time the
with the above settings for temperature, fan speed, and air flow direction. To
change the settings, repeat steps
NOTE:
• ECONO COOL operation can be set together with COOL mode for i-save operation.
• Timer operation can be used even if i-save operation is set.
To cancel i-save operation:
I
Press the button again.
i-save operation can also be cancelled by pressing the
i-save operation has been successfully cancelled if the operation indicator lamp on the right side of the indoor unit turns
off or changes from orange to green.
Usage of i-save operation:
1 Using as a low-energy mode
i-save operation can be used as a low-energy mode by setting the temperature 2–3 °C warmer than the normal cooling
temperature or 2–3 °C cooler than the normal heating temperature. This is good to use if a room is unoccupied or while
you are sleeping.
I Before leaving the room unoccupied:
· Press the button to switch to the low-energy mode before leaving the room.
· When you return to the room, the temperature will not be too hot or too cold.
· Press the button again and the air conditioner will operate with the normal settings for temperature, fan speed,
and air flow direction for a comfortable, air-conditioned environment.
I Before sleeping:
· Before going to sleep, press the button, and then go to your bedroom.
· While you are sleeping, the room will be air-conditioned using the low-energy mode until the following morning.
· In the morning, press the button again, and the air conditioner will operate with the normal settings for tempera-
ture, fan speed, and air flow direction. The set room temperature will be obtained quicker than if the air conditioner was
stopped while you were sleeping.
2 Using as a mode for frequent settings
If you often switch between two groups of settings for temperature, fan speed, and air flow direction in the same operation
mode, save one group of settings using the
by pressing the button, avoiding the troublesome remote controller operations.
MODE
button to select COOL or HEAT mode.
button.
TOO TOO
WARM COOL
and buttons to set the desired temperature.
button to set the desired air flow direction.
FAN
button to set the desired fan speed.
button is pressed, the air conditioner starts operating
1 – 3.
MODE
button to change the operation mode.
button. This will allow you to select the desired group of settings simply
9