Aritech EV1116 Serie Hoja De Instalación página 6

FCC Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the
equipment and receiver
•
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced
radio/TV technician for help
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
European Union Carrier Fire & Security hereby declares that this
directives device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see firesecurityproducts.com or
www.aritech.com.
Product may contain substances that are also
REACH
Candidate List substances in a concentration
above 0.1% w/w, per the most recently published
Candidate List found at ECHA Web site.
Safe use information can be found at
https://firesecurityproducts.com/en/content/intrusi
on-intro
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
recyclethis.info
Product Please consult the following weblink to retrieve
documentation the electronic version of the product
documentation.
This link will guide you to the EMEA regional
contact page. On this page you can request your
login to the secured webportal where all manuals
are stored.
https://firesecurityproducts.com/en/contact
Contact information
firesecurityproducts.com or www.aritech.com
6 / 38
DA: Installationsvejledning
Introduktion
EV1100-serien omfatter EV1116 og EV1116AM PIR-
rumdetektorer. De har patenteret spejl, pyro og
signalbehandlingsteknologi.
ADVARSEL! Udstyret er ikke jordet. Ethvert ekstern
kredsløb, der er tilsluttet udstyreret, skal være
placeret i den samme bygning og tilsluttes en
beskyttende jordleder.
Trådisolering af kabler, der er tilsluttet udstyret, skal være
i overensstemmelse med IEC 60332-1-2 og IEC 60332-1-3
eller IEC 60332-2-2, afhængig af ledningens tværsnit, eller
IEC TS 60695-11-21, uanset af tværsnitsarealet. Alternativ
skal sådanne ledninger være i overensstemmelse med
UL 2556 VW-1.
Installationsvejledning
Den anvendte teknologi i disse detektorer er modstandsdygtig
over for falske alarmer. Undgå imidlertid mulige årsager til
ustabilitet (se Figur 1), f.eks.:
• Direkte sollys på detektoren
• Kraftig træk på detektoren.
•
Varmekilder inden for detektorens synsfelt
•
Dyr inden for detektorens synsfelt
•
Blokering af detektorens synsfelt med store genstande
som f.eks. møbler
•
Genstand under 50 cm (20 in.) fra anti-maskeringsdetektor
(AM)
•
Installation af to detektorer mod hinanden og mindre end
50 cm (20 in.) fra hinanden (kun AM-detektorer)
Installation af detektoren
Figur 7
(1) Standardtilslutning
(fabriksstandard)
(2) Dobbelt sløjfe-tilslutning
CP Central
Sådan installeres detektoren:
Tag dækpladen af og fjern skruen (se Figur 2, trin 1).
1.
Åbn forsigtigt detektoren med en skruetrækker (Figur 2,
2.
trin 2 og 3).
Gør soklen fast til væggen. Til fladmontering anvendes
3.
mindst to skruer (DIN 7998) i position A. Til
hjørnemontering anvendes skruer i position B eller C
(Figur 3). Til at installere vægsabotagekontakt anvendes
position A eller C.
4. Tilslut detektoren (se figur 3 og 7).
Vælg de ønskede jumper- og DIP-switch-indstillinger (se
5.
figur 5). Se "Jumper-indstillinger" på side 7, hvis du ønsker
yderligere oplysninger.
Fjern afskærmningen og påsæt klæbemærker efter behov
6.
(se eksempel i Figur 6).
7. Til loftsmontering med 90 graders anvendelse benyttes
SB01-svingmonteringskonsol.
P/N 146251999-4-ML • REV M • ISS 10JUN21
WT Gangtest
AM Antimaskning
D/N Dag/nat
Rtest Fjernbetj test