Publicidad
Idiomas disponibles
Idiomas disponibles
MORE INFORMATION
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• For the latest compatible list and software versions of iPhone/iPod, see: www.kenwood.com/cs/ce/ipod
• You cannot operate iPod if "KENWOOD" or " " is displayed on iPod.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory (AOA) 2.0.
• If the Android device supports both mass storage class device and AOA 2.0, this unit always playback via
AOA 2.0 as priority.
• For more information and the latest compatible list, see: www.kenwood.com/cs/ce/
About Pandora
• Pandora is available only in the U.S., Australia and New Zealand.
• Because Pandora is a third-party service, the specifications are subject to change without prior notice.
Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.
• Some functions of Pandora cannot be operated from this unit.
• For issues using the application, please contact Pandora at pandora-support@pandora.com.
About iHeartRadio
• iHeartRadio® is a third-party service, therefore the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired or some or all of the services may become
unavailable.
• Some iHeartRadio® functionality cannot be operated from this unit.
Muting upon the reception of a phone call
Connect the MUTE wire to your telephone using a commercial telephone
accessory. ( 20)
When a call comes in, "CALL" appears. (The audio system pauses.)
• To continue listening to the audio system during a call, press
disappears and the audio system resumes.
When the call ends, "CALL" disappears. (The audio system resumes.)
18
INSTALLATION / CONNECTION
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery's negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or
Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car's chassis again after installation.
Caution
• For safety's sake, leave wiring and mounting to professionals. Consult the car
audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this
unit during and shortly after use of the unit. Metal parts such as the heat sink and
enclosure become hot.
• Do not connect the [ wires of speakers to the car chassis or Ground wire (black),
or connect them in parallel.
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle's fuse box which provides 12 V
DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on
the car are working properly.
• If the fuse blows, first make sure the wires are not touching car's chassis, then
replace the old fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then disconnect
the [ terminal of the car battery.
2
Connect the wires properly.
See Wiring connection. ( 20)
3
Install the unit to your car.
. "CALL"
See Installing the unit (in-dash mounting).
4
Connect the [ terminal of the car battery.
5
Reset the unit. ( 3)
Publicidad
