Publicidad
Idiomas disponibles
Idiomas disponibles
AUDIO SETTINGS
While listening to any source...
1
Press AUDIO to enter [AUDIO CONTROL].
2
Turn the volume knob to make a selection (see the following table),
then press the knob.
3
2
Repeat step
until the desired item is selected or activated.
4
Press and hold
to exit.
(or using RC-406)
1
Press AUD to enter [AUDIO CONTROL].
Press J / K to make a selection, then press
2
To return to the previous setting item, press
SUB-W LEVEL
–15 to +15 (0)
BASS LEVEL
–8 to +8 (+6)
MID LEVEL
–8 to +8 (+5)
TRE LEVEL
–8 to +8 (0)
EQ PRO
BASS ADJUST BASS CTR FRQ
BASS LEVEL
BASS Q FACTOR
BASS EXTEND
MID ADJUST
MID CTR FRQ
MID LEVEL
MID Q FACTOR
TRE ADJUST
TRE CTR FRQ
TRE LEVEL
14
.
.
Adjusts the subwoofer output level.
Adjusts the level to memorize for each source. (Before
making an adjustment, select the source you want to
adjust.)
60HZ/ 80HZ/ 100HZ/ 200HZ: Selects the center
frequency.
–8 to +8 (+6): Adjusts the level.
1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
ON: Turns on the extended bass. ; OFF: Cancels.
0.5KHZ/ 1.0KHZ/ 1.5KHZ/ 2.5KHZ: Selects the center
frequency.
–8 to +8 (+5): Adjusts the level.
0.75/ 1.00/ 1.25: Adjusts the quality factor.
10.0KHZ/ 12.5KHZ/ 15.0KHZ/ 17.5KHZ: Selects the
center frequency.
–8 to +8 (0): Adjusts the level.
PRESET EQ
BASS BOOST
LOUDNESS
SUBWOOFER SET
Default: XX
LPF SUBWOOFER
SUB-W PHASE
FADER
BALANCE
VOLUME OFFSET
SOUND RECNSTR
(Sound
reconstruction)
• [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is
selectable only if [SWITCH PREOUT] is set to [SUBWOOFER]. ( 4)
• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/
NATURAL/ USER: Selects a preset equalizer suitable to the music
genre. (Select [USER] to use the customized settings.)
[DRIVE EQ] is a preset equalizer that reduces noise outside the car or
running noise of the tyres.
LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred bass boost level. ;
OFF: Cancels.
LEVEL1/ LEVEL2: Selects your preferred low and high frequencies
boost to produce a well-balanced sound at a low volume level. ;
OFF: Cancels.
ON: Turns on the subwoofer output. ; OFF: Cancels.
THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/
160 Hz are sent to the subwoofer.
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [THROUGH] is selected for
[LPF SUBWOOFER].)
R15 to F15 (0): Adjusts the rear and front speaker output balance.
L15 to R15 (0): Adjusts the left and right speaker output balance.
For AUX: –8 to +8 (0) ; For other sources: –8 to 0: Presets the volume
adjustment level of each source. (Before adjustment, select the source
you want to adjust.)
ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost
in audio data compression. ; OFF: Cancels.
Publicidad
