Publicidad
Idiomas disponibles
Idiomas disponibles
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the
power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed.
Use of the power tool for operations different from
those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
(Original instructions)
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool
is maintained.
Additional Specific Safety Rules for Sanders
● Hold the power tool by insulated gripping surfaces,
because the sanding belt / sanding base may contact
its own cord. Cutting a "live" wire may make exposed
metal parts of the power tool "live" could give the operator
an electric shock.
● Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
workpiece by hand or against your body leaves it unstable
and may lead to loss of control.
● The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
@
risk of personal injury and/or damage to property.
WARNING: Contact with or inhalation of dusts arising
from sanding applications may endanger the health
of the operator and possible bystanders. Wear a dust
mask specifically designed for protection against
toxic dust and fumes and ensure that persons within
@
or entering the work area are also protected.
WARNING: Use this tool in a well-ventilated area
when sanding ferrous metals. Do not operate the tool
near flammable liquids, gases or dust. Sparks or hot
particles from sanding or arcing motor brushes may
@
ignite combustible materials.
WARNING: Do not use the dust filter cassette or the
dust extraction adaptor to store objects.
@
Sanding Paint
WARNING: Observe the applicable regulations for
sanding paint. Pay special attention to the following:
Whenever possible, use a vacuum extractor for
dust collection.
Take special care when sanding paint which is
possibly lead based:
Do not let children or pregnant women enter the work
area. All persons entering the work area should wear
a mask specially designed for protection against lead
paint dust and fumes.
Do not eat, drink or smoke in the work area.
Dispose of dust particles and any other removal
@
debris safely.
WARNING: We recommend the use of a residual
current device with a residual current rating of 30mA
or less.
ENGLISH
5
Publicidad
