Metabo KHE 5-40 Instrucciones De Manejo página 6

en ENGLISH
8 Sleeve *
9 Knob *
10 Button for continuous operation (KHE...: only in
chisel operating mode)
11 Metabo VibraTech (MVT): integrated damping
system
12 Trigger
13 Handle
14 Operation display*
15 Signal display *
16 Adjustment wheel *
* equipment-specific
5. Initial Operation
Before commissioning, check that the rated
mains voltage and mains frequency stated on
the type plate match your power supply.
Always install an RCD / GFCI with a maximum
trip current of 30 mA upstream.
Use only extension cables with a minimum cross-
section of 1.5 mm
correspond to the power consumption of the
machine (cf Technical Specifications). If a cable
roller is used, always roll up the cable completely.
5.1 Assembly of the bow handle or
additional handle
For safety reasons, always use the bow
handle (5) or additional handle (1) supplied.
MH 5, MHE 5:
Release the clamping ring by turning the clamping
knob (4) anticlockwise. Adjust the bow handle (5) to
the required position and angle. Tighten the
clamping knob firmly.
KHE 5-40:
Open the clamping ring by turning the additional
handle (1) anticlockwise. Secure the additional
handle at the required angle. Tighten the additional
handle.
6. Use
6.1 Depth Stop Setting
(only for KHE 5-40)
Release the wing (2) screw. Set the depth stop (3)
to the required drilling depth. Retighten the wing
screw (2).
6.2 Positioning, removing tool
Before inserting, clean tool shank and apply
supplied special grease (accessories: Order
no. 6.31800)! Use only SDS-max tools.
The dust protection cap (6) prevents the
ingress of drilling dust during operation. When
inserting the tool, pay attention to ensure that the
dust protection cap (6) is not damaged.
Positioning tool:
6
2
. Extension cables must
Hold the tool lock (7) in the front position when
inserting the tool. Turn tool and insert until it
engages. The tool is being locked.
Pull on the tool to check that it is correctly
seated. (It must be possible to move the tool a
few centimetres in an axial direction.)
Remove the tool:
Pull the tool lock (7) backwards in direction
indicated by arrow (a) and remove tool (b). See
page 2.
6.3 Setting operating mode and chisel
position
Avoid levering with the machine when a chisel
is fitted.
KHE 5-40:
Do not activate the switch button (9) until the
motor has completely stopped.
Turn the switch button (9) to select the desired
operating mode.
Hammer drilling
Chiselling
Setting which enables the chisel to be rotated
to the desired position.
Setting the position of the chisel: The chisel can be
locked in different positions.
- Insert the chisel.
- Turn the knob (9) to the interim position
- Turn the chisel to the required position.
- Turn the switch button (9) to position
- Turn the chisel until it engages.
When a chisel is fitted, only operate the
machine in the chiselling operating mode
MH 5, MHE 5:
The chisel can be locked in different positions.
- Insert the chisel.
- Push the sleeve (8) forwards and turn the chisel
until it is in the desired position.
- Push/ release the sleeve (8) backwards.
- Turn the chisel until it engages.
6.4 Switching on and off
Torque setting:
Press the trigger switch (12) to switch on the
machine.
To switch off release the trigger switch (12).
Continuous operation (only in chiselling
mode ):
The machine can be switched to continuous mode
(KHE...: only in chiselling mode
button (10) .
To switch off, press the (10) button once again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
.
.
.
) by pressing the