Metabo KHE 5-40 Instrucciones De Manejo página 7

both hands using the handles provided, stand
securely and concentrate.
6.5 Setting impact force
Rotate the adjustment wheel (16) to change the
impact strength (and speed). The impact strength is
increased from setting 1 to 5 and the mode display
(14) flashes. In setting 6, the tool delivers the
maximum impact strength, in this setting the mode
display (14) is constantly lit.
Scope of application
Plaster/light construction materials ............................ 1-2
Brickwork/removing tiles ............................................ 3-4
Drilling/chiselling into concrete .................................. 5-6
6.6 Metabo VibraTech (MVT)
For reduced vibrations and less stress on the
hands.
Always apply a moderate amount of pressure to the
handle when pushing down the machine and do not
force. Vibrations are reduced most effectively at the
central position (11).
7. Cleaning, Maintenance
The power tool should be cleaned regularly, often
and thoroughly through all air vents using a vacuum
cleaner or by blowing in dry air. Prior to this
operation, separate the power tool from the power
source and wear protective glasses and dust mask.
A damaged dust protection cap (6) must be
replaced immediately.
To replace the dust protection cap (6) slide the tool
lock (7) back. Grasp the dust protection cap and pull
firmly forwards and off. Fit the new dust protection
cap onto the spindle at an angle and press hard to
secure.
8. Troubleshooting
Overload:
The machine has shut down by itself. The
signal indicator (15) flashes. The machine was
overloaded (30%)! Let the machine cool down, only
then can you continue to work. Avoid further
overloading.
Restart protection:
The machine does not start. The signal
indicator (15) flashes. Restart protection is active.
If the mains plug is inserted with the machine
switched on or if the power supply is restored
following an interruption, the machine does not start
up. Switch the machine off and back on again.
Carbon brushes worn:
The signal indicator (15) flashes:
The carbon brushes are almost completely worn
(remaining operating time approx. 8 hours). If the
brushes are completely worn, the machine switches
off automatically. Have the brushes replaced by an
authorised service centre.
9. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
10. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
wheel
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
11. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
12. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P = Rated input power
1
P = Power output
2
T = Torque
n = No-load speed
1
D = Max. drilling diameter in concrete with
1
impact masonry bits
D = Max. drilling diameter in concrete with
2
impact core cutters
D = Max. drilling diameter in concrete with
3
milling cutters
s = Maximum impact rate
max
W = Single impact force
C = Number of chisel positions
m = Weight without mains cable
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value (hammer drilling
h, HD
into concrete)
a = Vibration emission value (chiselling)
h, Cheq
K
h,HD/Cheq
Typical A-effective perceived sound levels:
L = sound-pressure level
pa
= Uncertainty (vibration)
ENGLISH en
7