Publicidad
Idiomas disponibles
Idiomas disponibles
with a soft cloth, this way avoiding humidity on surfaces and
especially on gaps.
The rinsing and drying processes are extremely important
to prevent stains and corrosion from arising.
Acid solutions, salty solutions, disinfectants and some
sterilizing solutions (hypochlorites, tetravalent ammonia
salts, iodine compounds, nitric acid and others), must be
AVOIDED, once it cannot remain for long in contact with
the stainless steel.
These substances attack the stainless steel due to the
CHLORINE on its composition, causing corrosion spots
(pitting).
Even detergents used in domestic cleaning must not remain
in contact with the stainless steel longer than the necessary,
being mandatory to remove it with plain water and then dry
the surface completely.
Use of abrasives:
Sponges or steel wools and carbon steel brushes, besides
scratching the surface and compromising the stainless
steel protection, leave particles that rust and react
contaminating the stainless steel. That is why such products
must not be used for cleaning and sanitization. Scrapings
made with sharp instruments or similar must also be
avoided.
Main substances that cause stainless steel corrosion:
Dust, grease, acid solutions such as vinegar, fruit juices, etc.,
saltern solutions (brine), blood, detergents (except for the
neutral ones), common steel particles, residue of sponges
or common steel wool, and also other abrasives.
4. Safety Notions
The following safety instructions are addressed to both the
operator of the machine as well as the person in charge of
maintenance.
The machine has to be delivered only in perfect conditions
of use by the Distributor to the user. The user shall operate
the machine only after being well acquainted with the
safety procedures described in the present manual READ
THIS MANUAL CAREFULLY.
The change in the protection system and the appliance
safety devices will lead to serious risks to physical integrity
of the people during operation, cleaning, maintenance
and shipping according to ISO 12100 standard.
4.1 Basic Operation Practice
4.1.1 Danger
Some areas of the electric device have parts that are
connected or have parts connected to high voltage. These
parts when touched may cause severe electrical chocks or
even be fatal.
Never touch switches such as buttons, turning switchs and
knobs with your hands wearing wet clothes and/or wet
shoes. By not following these instructions operator could
be exposed to severe electrical shocks or even to a fatal
situation.
14
4.1.2 Warnings
The operator has to be well familiar with the position of ON/
OFF Switch to make sure the Switch is easy to be reached
when necessary. Before any kind of maintenance, physically
remove plug from the socket.
Provide space for a comfortable operation thus avoiding
accidents.
Water or oil spilled on the floor will turn it slippery and
dangerous.
Make sure the floor is clean and dry to avoid accidents.
If any work is to be made by two or more persons,
coordination signs will have to be given for each operation
step.
Every step of the operation shall be taken only if a sign has
been made and responded.
Read the INSTRUCTONS in the manual before turning
on the equipment. Make sure that the information as
understood. If you have any questions, check the Skymsen.
4.2 Precautions and Observations before Turning
on the Equipment
4.2.1 Danger
An electric cable or electric wire with damaged jacket or bad
insulation could cause electrical chocks as well as electrical
leak. Before using the equipment, check conditions of all
wires and cables.
4.2.2 Advices
Be sure ALL INSTRUCTIONS in this manual have been
thoroughly understood.
Every function and operational procedure have to be very
clear to the operator. Contact your nearest Dealer for
further questions.
Any manual command (switch, button or lever) shall be
given only after being sure it is the correct one.
4.3 Routine Inspection
4.3.1 Cautions
Check the motor and the sliding and spinning parts of the
appliance, in case of abnormal noise.
Check the protections and devices so that they always work
properly.
4.4 Operation
4.4.1 Advices
Do not work with long hair that may touch any part of the
appliance, because they may cause serious accidents. Tie
them up and to the back, cover it with a scarf.
- Only trained and qualified users can operate the appliance.
- NEVER operate the appliance without any safety equip-
ment.
Publicidad
