Forch 5331 1 18 3 Manual Original página 15

Do not use the power tool if the switch does
u
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
Disconnect the plug from the power source
u
and/or remove the battery pack, if detach-
able, from the power tool before making any
adjustments, changing accessories, or stor-
ing power tools. Such preventive safety meas-
ures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of
u
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
Maintain power tools and accessories.
u
Check for misalignment or binding of mov-
ing parts, breakage of parts and any other
condition that may affect the power tool's
operation. If damaged, have the power tool
repaired before use. Many accidents are
caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool
u
bits etc. in accordance with these instruc-
tions, taking into account the working condi-
tions and the work to be performed. Use of
the power tool for operations different from
those intended could result in a hazardous situ-
ation.
Keep handles and grasping surfaces dry,
u
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpec-
ted situations.
Battery tool use and care
Recharge only with the charger specified by
u
the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
Use power tools only with specifically desig-
u
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
When battery pack is not in use, keep it
u
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a connec-
tion from one terminal to another. Shorting
the battery terminals together may cause burns
or a fire.
1 609 92A 7MC • 28.11.22
English
Under abusive conditions, liquid may be
u
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with wa-
ter. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
Do not use a battery pack or tool that is
u
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire
u
or excessive temperature. Exposure to fire or
temperature above 130°C may cause explo-
sion.
Follow all charging instructions and do not
u
charge the battery pack or tool outside the
temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Never service damaged battery packs. Ser-
u
vice of battery packs should only be performed
by the manufacturer or authorized service pro-
viders.
Hammer Safety Warnings
Safety instructions for all operations
Wear ear protectors. Exposure to noise can
u
cause hearing loss.
Use auxiliary handle(s), if supplied with the
u
tool. Loss of control can cause personal injury.
Hold the power tool by insulated gripping
u
surfaces, when performing an operation
where the cutting accessory or fasteners
may contact hidden wiring . Cutting accessory
or fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Safety instructions when using long drill bits
with rotary hammers
English
Always start drilling at low speed and with
u
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if allowed
to rotate freely without contacting the workpiece,
resulting in personal injury.
Apply pressure only in direct line with the bit
u
and do not apply excessive pressure. Bits
English
English
English | 15