BH FITNESS G818RBM Instrucciones De Montaje Y Utilización página 16

(93) Left swing arm rear cover.
(94) Right swing arm front cover.
(95) Right swing arm rear cover.
(97) Left pedal post.
(103) Right pedal post.
(104) Left pedal.
(105) Right pedal.
(106) Left connection tube.
(108) Right connection tube.
(110) Cushion plate.
(111) Left swing post.
(112) Right swing post.
(113) Console.
(117) Adaptor.
Fig.2 Fasteneers List:
(124) Screw M8x40.
(125) Self-locking nut. M8
(126) Screw ST3x10.
(127) Hex Screw.
(132) Screw M10x65.
(133) Self-locking nut. M10.
(134) Screw M5x16.
(135) Screw M10x50.
(137) Screw M8x25.
(141) Curved washer.
158) Washer D10.
(
(159) Washer D10.
(120) Cap.
(121) Screw M8x20.
(122) Plunge D8x28,5.
(123) Screw D4x12.
(128) Washer D8,5x16.
(129) Washer D8,2x15,4.
(138) Screw M5x12.
Wrenches.
2.
FITTING THE LOWER TUBES.-
ATTENTION: The assistance of a second person is
required for this stage of the assembly.
Bring the left connection tube (106) to the main body
(1), and place it according to figure Fig.3, Insert screws
(127) and tighten securely.
Perform the same assembly with the right hand and the
right connection tube (108).
3.-
FITTING THE ADJUSTABLE FEET.-
Take the left pedal tube (97) marked with the letter (L),
place the cushion plate (110) as shown in Fig.4. Then
place the left pedal (104) and secure with screws
(134).
Perform the same assembly with the right footrest
assembly (103) marked with the letter (R) and the right
pedal (105) Fig.4.
4.-
FITTING THE REAR STABILISER.
Move the upper part of the left pedal tube (96) to the
arm of the central body (1), insert it into the arm as
sohwn in Fig.5. Place the bushings (144), Fig.5, and
tighten them securely.
Then close the bottom part of the left pedal tube (96) to
the regulatory arm of the central body (1), and insert it
into the arm Fig.5A.
Place the screws (132), together with the washers
(158), (159) and
Perform the same steps of the right pedal tube
assembly (102).
5.-
FITTING THE FOOT REST FOCUS
BARS.-
Bring the left handle connection tube
body (1), placing it according to the Fig.6. Insert screws
(137) with washers (129) and screws (135) on the back
joining with left connection tube
tighten securely. Perform the same steps with the right
handle connection tube.
6.-
FITTING THE SWING POSTS.-
Move the left swing post
main body (1), Fig.7.and insert it. Fix with screws (124)
together with nylon nuts (125) and washers (141) Fig.7
and tighten securely. Perform the same with your right
hand and right swing post
covers of the swing posts (92) and (94) and the rear
covers (93) and (95) as shown in Fig 8.and screw them
with the screws (126).
7.-
FITTING THE MONITOR POST.-
Insert the joints (122) in the cover (84). Take hold of
the front post (81) and fit the lower tray (5) and the
cover (84) as shown in Fig.9. Connect the wires of the
main body with the wires of the front post, Fig.9.
Insert the front post (84) onto the boss on the main
body (1).
Insert the screws (121), washers (128), (129), Fig.9,
and tighten securely.
Lower the cover (84).
8.-
FITTING THE FIXED HANDLEBAR.-
Place the fixed handle bar
external part of the man body (1) Fig.10, taking special
acoount to insert wires handgrip and taking them
through the slot where the monitor will be
Fit the screws (121) and the washers (128), (129),
Fig.10.
IMPORTANT: It is advisable to retighten these
screws after one month of using the machine.
9.-
FITTING THE MONITOR.-
Remove the back monitor cover. Place the monitor
(113) onto the front post plate as shown in Fig. 11 and
fit the screws (138).
Connect the terminals coming out of the front post and
of the monitor, Fig.11.
Refit the back monitor cover with the screws, Fig.11.
16
(133) and tighten
(82) to the central
(106) after aligning and
(83).
(111) to the outer tube on the
(112). Then place the frontal
(34) and insert it into the
placed.
securely.