Descargar Imprimir esta página

Bosch GSR Professional 18V-110 C Manual Original página 19

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 29
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Starting Operation
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (16) to the middle posi-
tion to avoid unintentionally switching it on. Insert the
charged battery (11) into the handle until you feel it engage
and it is flush with the handle.
Setting the rotational direction (see figure B)
The rotational direction switch (16) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (17) is being pressed.
Rotate clockwise: Slide the rotational direction
switch (16) on both sides until it stops in the
tion.
Rotate anti-clockwise: Slide the rotational direction
switch (16) on both sides until it stops in the
tion.
Setting the operating mode
Drilling
Set the mode selector switch (8) to the
"drilling" symbol.
Screwdriving
Set the mode selector switch (8) to the "screw-
driving" symbol.
Impact drilling(GSB 18V-110 C)
Set the mode selector switch (8) to the "impact
drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(17).
The LED (13) lights up when the on/off switch (17) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (17).
Bosch Power Tools
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (17) to varying extents.
A light pressure on the on/off switch (17) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Preselecting torque (applies to screwdriving mode)
The torque presetting ring (7) can be used to preselect the
required torque in 25 stages. Once the set torque has been
reached, the application tool will be stopped.
Mechanical gear selection
Only operate the gear selector (9) when the power
u
tool is not in use.
First gear:
Low speed range; for working with a large drilling diameter
or for screwdriving.
Second gear:
High speed range; for working with a small drilling diameter.
Always push the gear selector switch as far as it will
u
go. Otherwise, the power tool may become damaged.
Temperature-dependent overload protection
When used as intended, the power tool cannot be over-
loaded. In the event of overloading or the temperature
rising/falling outside the permitted operating temperature
range, the speed will be reduced. The power tool will not run
at full speed again until the permitted operating temperature
has been reached.
Activation of the temperature-controlled overload protector
posi-
is indicated by the LED (14) on the power tool lighting up
red. To return to within the permitted operating temperature
range, switch the gear selector (9) to first gear, run the
power tool at no load or wait until the LED (14) goes out.
posi-
When the LED (14) has gone out, the tool has returned to
within the permitted operating temperature range.
Emergency switch-off (KickBack Control)
The emergency switch-off function (Kick-
Back Control) gives the user greater control
over the power tool and offers them better
protection than power tools that do not
have KickBack Control. The power tool will switch off if it
suddenly and unforeseeably rotates around the drilling
axis.
Rapid shut-off is indicated by the LED on the power tool
flashing.
To switch the tool back on, release the on/off switch and
then press it again.
If the Kickback Control function is defective, it will no
u
longer be possible to switch the power tool on. Have
the power tool serviced by a qualified repair person
using only original replacement parts.
Connectivity functions
In conjunction with the Bluetooth® Low Energy Module
GCY 30-4, the following connectivity functions are available
for the power tool:
English | 19
1 609 92A 60C | (07.08.2020)

Publicidad

loading

Este manual también es adecuado para:

Gsb professional 18v-110 c