DeWalt D25811 Manual De Instrucciones página 22

ENglIsh
Performing an Application (Fig. A, G)

WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly.
NoTE: Operating temperature of this tool is 19˚ to 104˚ F
(-7 to +40˚ C). Using the tool outside of this temperature
range will decrease the life of the tool.
1. Insert the appropriate chisel and rotate it by hand
to lock it into the desired position.. Refer to Bit and
Bit Holder.
2. Using the mode selector dial
Refer to Mode Selection.
3. Adjust the side handle 2
Fig. G
4
2
4. Place the bit/chisel on the desired location.
5. Depress the trigger switch
the trigger switch, the faster the tool will operate. For
maximum tool life, use variable speed only for starting
holes or fasteners.
6. To stop the hammer, release the switch.

WARNING:
• Do not use this tool to mix or pump easily
combustible or explosive fluids (benzine,
alcohol, etc.).
• Do not mix or stir inflammable liquids
labelled accordingly.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
20
4 , select chipping mode .
as necessary.
1
1 . The farther you depress
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Estão disponíveis vários tipos de brocas e cinzeis hexagonais
e SDS-Max e de 17 mm como opção. Os acessórios
e dispositivos complementares utilizados devem ser
lubrificados regularmente à volta do equipamento.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D WALT factory service center
e
or a D WALT authorized service center. Always use
e
identical replacement parts.
Protecting the Environment
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. .
specifications
D25810-AR
220V ~
Voltage
50Hz
Power
1050 W
Beats per Minute
3150 ipm
specifications
D25811-AR
220V ~
Voltage
50Hz
Power
1050 W
Beats per Minute
3150 ipm
WALT
e
D25810-B2 D25810-B3 D25810-BR
220V ~ 120V ~ 127V ~
50-60Hz 50-60Hz 60Hz
1050 W 1050 W 1050 W
3150 ipm 3150 ipm 3150 ipm
D25811-B2 D25811-B3 D25811-BR
220V ~ 120V ~ 127V ~
50-60Hz 50-60Hz 60Hz
1050 W 1050 W 1050 W
3150 ipm 3150 ipm 3150 ipm