Tripp-Lite SR42UBCL Manual Del Propietário página 2

1. Important Safety Instructions
SAVE THESE INSTRUCTIONS
All sections of this manual contain instructions and warnings that should be followed during the installation and use of the SmartRack
Enclosures described in this manual. Read all instructions and warnings thoroughly before attempting to move, install or use the SmartRack
Enclosures described in this manual. Failure to comply will create a risk of personal injury and property damage and may invalidate the
warranty.
• Keep the enclosure in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive
contaminants, dust and direct sunlight.
• Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external ventilation
openings ofthe enclosure.
• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it unassisted. Use a mechanical
device such as a forklift or pallet jack to move the enclosure in the shipping container.
• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures.
• Inspect the shipping container and the enclosure for shipping damage. Do not use the enclosure if it is damaged.
• Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible. The casters are designed for
minor position adjustments within the final installation area only. The casters are not designed for moving the enclosure over longer distances.
• The casters are not designed to provide long-term support for the enclosure after final installation. Use the levelers to provide long-term support.
• Install the enclosure in a structurally sound area with a level floor that is able to bear the weight of the enclosure, all equipment that will be installed in
the enclosure and any other enclosures and/or equipment that will be installed nearby.
• Install the cabinet securely to the building structure, using the shipping brackets as illustrated in the Enclosure Installation section of this manual.
• Do not push the enclosure from the side panels to move it. Pushing from the side panels will cause a tipping hazard.
• When rolling the enclosure on its casters, always push it from behind, never pull it toward you.
• A rolling enclosure can cause personal injury and property damage if not properly supervised. If rolling the enclosure down a ramp is required, use
extreme caution. Do not attempt to use ramps that have a slope steeper than 1:12.
• Use caution when cutting packing materials. The enclosure could be scratched, causing damage not covered by the warranty.
• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may cause product damage that will
void the warranty.
• Do not re-ship the enclosure with additional equipment unless the enclosure was shipped with a special shock pallet ("SP1" models only). The combined
weight of the enclosure and installed equipment must not exceed the load capacity of the pallet. Tripp Lite is not responsible for any damage that occurs
during re-shipment.
• DANGER: STABILITY HAZARD, RACKS ARE TO BE INSTALLED BY QUALIFIED SERVICE PERSONNEL ONLY.
• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support
equipment or to significantly affect its safety or effectiveness is not recommended.
2. Overview
SmartRack Enclosures accommodate all standard
19-inch rackmount equipment, regardless of
vendor, and ship fully assembled for quick and easy
deployment. They feature adaptable, heavy-duty
cabinets in 25U, 42U and 48U heights, with or
without side panels. Several models are available
with an integrated shock pallet that allows resellers,
integrators and enterprise customers to pre-
configure equipment and re-ship the enclosures to
the final installation site.
SmartRack Enclosures have variable mounting
depths, ideal for servers. Integrated baying
hardware enables cost-effective, orderly and
efficient expansion. The cabinets include quick-
release doors and side panels for convenient
maintenance and split front and front and rear
doors (select models) for improved access and
reduced clearance requirements. Front access
doors are reversible for installation flexibility. Front
and rear doors and side panels are lockable.
Available SmartRack Enclosures
Model #
SR25UB
SR25UBEXP
SR25UBSP1
SR25UBEXPSP1
SR42UB
SR42UBCL
SR42UBEXP
SR42UBSP1
SR42UBEXPSP1
SR48UB
SR48UBCL
SR48UBEXP
SR48UBSP1
SR48UBEXPSP1
See the Specifications section for more information.
2
Rack Height Side Panels
25U Yes
25U No
25U Yes
25U No
42U Yes
42U Yes
42U No
42U Yes
42U No
48U Yes
48U Yes
48U No
48U Yes
48U No
Shock Pallet
No
No
Yes
Yes
No
No
No
Yes
Yes
No
No
No
Yes
Yes