Publicidad
Idiomas disponibles
Idiomas disponibles
Special safety information for grinding/san-
ding and cutting-off
a) Use only grinding/sanding wheels that have
been approved for your electric tool and the
safety hood designed for these grinding/san-
ding wheels. Grinding/sanding wheels which
are not designed for the electric tool cannot
be shielded adequately and are unsafe.
b) The safety hood must be securely fastened to
the electric tool and adjusted so that it off ers
maximum safety, in other words it prevents
the smallest possible part of the grinding/
sanding wheel from striking the operator. The
safety hood is designed to protect the opera-
tor from broken pieces and accidental contact
with the grinding/sanding wheel.
c) Grinding/sanding wheels may only be used
for the applications for which they are recom-
mended. For example: Never grind/sand a
side surface area with a cutting-off wheel.
Cutting-off wheels are designed for removing
material with the edge of the wheel. Applying
lateral force to these cutting-off wheels can
cause them to break.
d) Always use undamaged clamping fl anges of
the correct size and shape for the grinding/
sanding wheel you have selected. Suitable
fl anges support the grinding/sanding wheel
and thus reduce the risk of the grinding/san-
ding wheel breaking. Flanges for cutting-off
wheels may diff er from the fl anges for other
grinding/sanding wheels.
e) Do not used worn grinding/sanding wheels
from larger electric tools. Grinding/sanding
wheels for larger electric tools are not desig-
ned for the higher speeds of smaller electric
tools and may break.
Other special safety information for cutting-
off wheels
a) Avoid blocking the cutting-off wheel or apply-
ing excessive contact pressure. Do not make
any excessively deep cuts. Overloading the
cutting-off wheel will increase the stress on
it and its susceptibility to jam or block and
therefore the possibility of recoil or of the grin-
ding wheel breaking.
b) Avoid the area in front of and behind the rota-
ting cutting-off wheel. If you move the cutting-
off wheel in the workpiece away from yourself,
in the event of recoil the electric tool and the
rotating wheel may be catapulted directly to-
wards you.
c) If the cutting-off wheel jams or you interrupt
your work, switch off the tool and hold it
Anl_SA_TC_AG_850_SPK8.indb 19
Anl_SA_TC_AG_850_SPK8.indb 19
GB
still until the wheel has reached a complete
standstill. Never attempt to pull the cutting-off
wheel out of the cut whilst it is still rotating,
otherwise it may suff er recoil. Find and rectify
the cause of the jam.
d) Do not switch the electric tool on again whilst
it is inside the workpiece. Allow the cutting-off
disk to reach its full speed before you conti-
nue the cut with care. Otherwise the wheel
may catch, jump out of the workpiece or
cause recoil.
e) Support panels or large workpieces to redu-
ce the risk of recoil by a jammed cutting-off
wheel. Large workpieces may sag under their
own weight. The workpiece must be suppor-
ted on both sides of the wheel both near the
cut and also at the edge.
f)
Be particularly careful with "pocket cuts" in
existing walls or in areas which you cannot
see clearly. As the cutting-off disk enters the
cut it may suff er recoil if it cuts into gas or wa-
ter pipes, electric cables or other objects.
Do not lose these safety instructions
2. Layout (Fig. 1)
1. Spindle lock
2. ON/OFF switch
3. Additional handle
4. Guard
5. Flange nut wrench
3. Items supplied
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any pa-
ckaging and/or transportation braces
(if available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
IMPORTANT
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
- 19 -
17.10.2017 09:03:01
17.10.2017 09:03:01
Publicidad
