Publicidad
Idiomas disponibles
Idiomas disponibles
TECHNICAL DATA
Die Grinder
Production code
Battery voltage
Rated speed
Collet diameter
Abrasive grinding body diam. max.
Weight according EPTA-Procedure 01/2014 (Li-lon 5,0 Ah)
Noise information
Measured values determined according to BS EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to BS EN 60745
Vibration emission value a
h
Uncertainty K=
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
BS EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications,
with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
DIE GRINDER SAFETY WARNINGS
Safety warnings common for grinding:
a) This power tool is intended to function as a grinder.
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, fire and/
or serious injury.
b) Operations such as sanding, wire brushing, polishing or
cutting-off are not recommended to be performed with this
power tool. Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool manufacturer. Just
because the accessory can be attached to your power tool, it does
not assure safe operation.
d) The rated speed of the grinding accessories must be at
least equal to the maximum speed marked on the power
tool. Grinding accessories running faster than their rated speed
can break and fly apart.
e) The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately controlled.
f) The arbour size of wheels, sanding drums or any other
accessory must properly fit the spindle or collet of the pow-
er tool. Accessories that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively and may
cause loss of control.
g) Mandrel mounted wheels, sanding drums, cutters or
other accessories must be fully inserted into the collet or
chuck. If the mandrel is insufficiently held and/or the overhang of
the wheel is too long, the mounted wheel may become loose and
be ejected at high velocity.
h) Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and cracks,
sanding drum for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory
and run the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break apart during this
test time.
i) Wear personal protective equipment. Depending on ap-
plication, use face shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing protectors, gloves and
shop apron capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or respirator
must be capable of filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause hearing loss.
M18 FDG
4582 21 02...
... 000001-999999
18 V
27000 min
-1
6 / 8 mm
50 mm
2,1 kg
86,1 dB (A)
97,1 dB (A)
12,0 m/s2
GB
D
1,5 m/s2
Deutsch
English
11
11
Publicidad
