Publicidad
Idiomas disponibles
Idiomas disponibles
extension cord is to be used outdoors, it must be marked
with the suffix W-A after the cord type designation. For
example, a designation of SJTW-A would indicate that the
cord would be appropriate for outdoor use. For proper size
cords see chart below.
Minimum Gauge for Cord Sets
Volts
Total length of cord in feet
120V
0-25
26-50
(0-7,6m)
(7,6-15,2m)
240V
0-50
51-100
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More than
Not more than
0 - 6
18
6 - 10
18
10 - 12
16
12 - 16
14
Warning! ome spray materials contain chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. To reduce your
exposure wear appropriate safety equipment such as
face masks, gloves, and other appropriate protective
equipment. Please review and follow the safety
precautions on the paint container.
Warning! Be sure to use appropriate protective gear
and unplug unit.
Warning! Make sure area is well ventilated and free of
flammable vapors.
Aligning the pickup tube (FIG B and B1)
The pickup tube can be aligned in the direction that you
will be doing the most spraying to help minimize the
amount of times that you will have to refill the canister.
f If you are spraying at an upward angle or straight on,
position the pickup tube (Figure B) toward the back
of the canister.
f If you are spraying at a downward angle, position
the pickup tube (Figure B1) toward the front of the
canister.
This will ensure you spray as much material as possible
before you need to refill.
Liquid material preparation (FIG C, C1 and C2)
TIP: Make sure the type of material you use can be
cleaned with either mineral spirits or paint thinner
(for oil-based paints) or a warm water and soap
solution (for water soluble paints like latex). Use drop
cloths during pouring, mixing, and viscosity testing
of materials to be sprayed to protect your floors and
anything else in the spraying area that you wish to
51-100
15,2-30,4m) 30,4-45,7m)
101-200
American Wire Gauge
16
16
16
14
16
14
12
No se recomienda
SET-UP
remain untouched.
The liquid being sprayed may need to be thinned (diluted)
before starting. When thinning, use the proper liquid
thinner recommended on the container by the material
manufacture.
Warning! Do not use materials with a flashpoint higher
than 60ºC (140ºF).
101-150
A 2-
201-300
when transferring spray material from the original
container into the bucket for thinning and
measuring purposes (Figure C).
A viscosity test cup is provided to determine the
14
"runout time" of the material being used.
12
12
f Before measuring for the proper viscosity, stir the
material thoroughly.
f Dip the viscosity cup into the material being sprayed
and fill the cup completely.
f With the cup held over the material container,
measure the amount of time it takes for the stream
of material flowing out to "break" or stop being a
constant stream out of the bottom of the cup (2
minutes or less) (Figure C1). This is the "runout time"
Refer to the thinning table for information on the
thinning required for different materials.
f If material needs thinning, add the appropriate liquid
thinning material recommended by the manufacturer
(Figure C2).
f It is possible to spray latex paint with this unit,
however, the required thinning may exceed material
manufacturer´s recommendation. Thin latex paint so
that it runs through viscosity cup in under 2 minutes.
The operator should con- sider the type of application
and final location of the project when spraying a
material that requires more than 2 min- utes to run
through the viscosity cup.
f
SPRAY MATERIAL
Clear and semi-transparent
stains and sealers Oil based
primers, varnishes and
polyurethane
Solid color water based stains
Water based or latex paints
Note: Not recommended for textured paint.
PREPARATION TIPS
f Always stir and strain the material thoroughly before
PORTUGUÊS • 15
quart mixing bucket is provided to use
3/4
THINNING TABLE
No thinning required
(Less than 2 minute
runout)
May require thinning
(More than 2 minute
runout)
RUNOUT TIME
Publicidad
