Balluff BIP AD2-T017-01-EB -S49 Serie Manual De Instrucciones página 9

BIP A/CD2-T017-01-EB/EP _ _ (-S4/S49)
Inductive Position System
Technical data
Accuracy
The specifications are typical values for
BIP-A/CD2-T017-01-EB/EP _ _ (-S4/S49) at room
temperature. The BIP reaches its full accuracy after a
warm-up period of 15 min under constant ambient
conditions. The duration of warm-up depends on the
ambient conditions.
Measuring range S
l
Linearity range S
l
Max. non-linearity
Reference distance S
e
Repeat accuracy
Sampling rate
Response time
Ambient conditions 1)
Ambient temperature T
a
BIP AD2-T017-01-EB/EP_ _
BIP CD2-T017-01-EB/EP_ _
Storage temperature
Temperature drift max. from end
value
Degree of protection per IEC 60529
Shock rating
per EN 60068-2-27
Vibration load
per EN 60068-2-6
Degree of contamination
Supply voltage (external)
Operating voltage U , stabilized
B
Rated operating voltage U
e
No-load current I at U
o e
Residual ripple (% of U )
e
Rated insulation voltage U
I
Short-circuit protection
Protected against miswiring
Polarity reversal protected
Output
BIP AD2-T017-01-EB/EP_ _
Output voltage at S
l
Output voltage at S
e
Load resistance R
L
BIP CD2-T017-01-EB/EP_ _
Output current at S
l
Output current at S
e
Load resistance R
L
www.balluff.com
0...17 mm
0...17 mm
±250 µm
8.5 mm
±50 µm
≥ 600 Hz
2.5 ms
–25...+70 °C
–10...+70 °C
–40...+85 °C
±3 %
IP67
30 g/11 ms
55 Hz, 1 mm
amplitude,
3 × 30 min
3
2) 15...30 V DC
24 V DC
≤ 20 mA
≤ 10 %
75 V DC
Yes
Yes
Yes
0...10 V
5 V
≥ 2000 Ω
4...20 mA
12 mA
≤ 500 Ω
Mechanical
Connection type
BIP A/CD2-...-EB/EP _ _
BIP A/CD2-...-EB/EP _ _ -S4
BIP A/CD2-...-EB/EP _ _ -S49
Housing material
Tightening torque
Sensing surface, material
Cable connection
Cable jacket, material
Cable diameter
Number of conductors
Wire cross-section
Shielding
BIP A/CD2-...-EB_ _
BIP A/CD2-...-EP_ _
Bending radius, fixed cable
1) For UL: Use in enclosed spaces and up to a height of 2000 m above sea
level.
2) For UL: The BIP must be externally connected via a limited-energy circuit
as defined in UL 61010-1, a low-power source as defined in UL 60950-1
or a class 2 power supply as defined in UL 1310 or UL 1585.
Accessories
BAM TG-XE-020 target
(order code: BAM02RW)
The position detected by the BIP (A) lies in the center
of the target (line of symmetry).
Material: Steel (EC-80)
6
A
28
18
BAE PD-XE-005 calibration box
(order code: BAE00T3)
Cable
Cable with S4
connector
Cable with S49
connector
PA
0.5 Nm
PA
PUR
≤ 3.5 mm
3
0.14 mm²
Yes
No
≥ 3 x cable
diameter
english 4