Descargar Imprimir esta página

EINHELL GE-BC 33 AS Manual De Instrucciones Original página 27

Ocultar thumbs Ver también para GE-BC 33 AS:

Publicidad

Idiomas disponibles

Idiomas disponibles

It may change according to how the equipment
is used and may exceed the specifi ed value in
exceptional circumstances.
The specifi ed vibration value can be used to com-
pare the equipment with other power tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect con-
ditions.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Assembly
5.1 Mounting the blade guard hood
Important: The cutting blade guard hood must be
fi tted if you wish to work with the cutting blade.
The guard hood for the cutting blade must be ins-
talled as shown in Figures 10-11.
5.2 Joining the drive rod mechanism to the
connecting piece (Fig. 4-7)
Fit the handle screw (Item 10) as shown in Fig.
4. Open the handle screw and push the drive rod
mechanism (Item 4) into the connecting piece
(Item 5). Make sure that the centering lever (Item
R) latches in the guide hole (Fig. 5/Item H). Tigh-
ten the handle screw.
To take apart, undo the handle screw. Unlock the
Anl_SA_GE_BC_33_AS_SPK8.indb 27
Anl_SA_GE_BC_33_AS_SPK8.indb 27
GB
centering lever and simultaneously pull the drive
rod mechanism out of the connecting piece.
5.3 Fitting / Replacing the cutting blade
The procedure for fi tting the cutting blade is
shown in Figures 12-18. To dismantle, proceed in
reverse order.
Fit the carrier plate 30) onto the spline shaft
(Fig. 13)
Secure the cutting blade (1) on the carrier
plate (Fig. 14)
Place the pressure plate (31) over the thread
of the spline shaft (Fig. 15)
Plug on the cover of the pressure plate (32)
(Fig. 16)
Mount the nut (24) hand-tight (Fig. 17).
While pressing the locking lever (A), turn on
the nut until the carrier plate is held in posi-
tion. Tighten the nut with a suitable tool (Fig.
18). Important: Left-hand thread!
Check whether the blade (1) can rotate freely
after you let go of the locking lever. If this is
not the case, have the mechanism checked
by an expert.
5.4 Fitting the cutting line guard hood to the
blade guard hood
Important: The cutting line guard hood must be
fi tted in addition if you want to work with the cut-
ting line.
The procedure for fi tting the guard hood for the
cutting line is shown in Figures 19-20. A blade
(Fig. 19/ Item F) on the underside of the guard
hood automatically cuts the cutting line to the
optimum length. It is covered by a guard (Fig.
19/Item G). Remove the guard before you start
working and replace it when you have fi nished
working.
5.5 Fitting the handle
Fit the handle as shown in Fig. 8-9.
5.6 Fitting / replacing the line spool
Fit the carrier plate (30) onto the spline shaft (Fig.
13)
While pressing the locking lever (A), turn on the
line spool until the carrier plate is held in position.
Tighten the line spool by hand (Fig. 21). Impor-
tant: Left-hand thread!
Check whether the line spool (3) can rotate freely
after you let go of the locking lever. If this is not
the case, have the mechanism checked by an
expert.
- 27 -
07.08.2017 09:00:42
07.08.2017 09:00:42

Publicidad

loading