Descargar Imprimir esta página

EINHELL GE-BC 33 AS Manual De Instrucciones Original página 28

Ocultar thumbs Ver también para GE-BC 33 AS:

Publicidad

Idiomas disponibles

Idiomas disponibles

6. Before starting the equipment
Before you connect the equipment to the mains
Check the equipment for the following each time
before use:
That there are no leaks in the fuel system.
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
That all screws are securely fastened.
That all moving parts move smoothly.
6.1 Fuel and oil
Recommended fuels
Use only a mixture of unleaded petrol and special
2-stroke engine oil. Mix the fuel mixture as indica-
ted on the fuel mixing table.
Important: Do not use a fuel mixture which has
been stored for longer than 90 days.
Important: Never use 2-stroke oil with a recom-
mended mixing ratio of 100:1. The manufacturer's
warranty will be voided in case of engine damage
due to inadequate lubrication.
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke
oil into the mixing bottle (see scale printed on the
bottle). Then shake the bottle well.
6.2 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol
1 liter
5 liters
Anl_SA_GE_BC_33_AS_SPK8.indb 28
Anl_SA_GE_BC_33_AS_SPK8.indb 28
GB
2-stroke oil
25 ml
125 ml
- 28 -
7. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from town to
town.
Before starting up the equipment remove the pro-
tective caps from the cutting blade.
7.1 Starting with a cold engine
Fill the tank with the required amount of oil/petrol
mix. See „Fuel and oil".
1. Set the equipment down on a hard, level sur-
face.
2. Press the fuel pump (primer) (Fig. 2/Item 29)
10 times.
3. Move the On/Off switch (Fig. 2/Item 9) to „I".
4. Set the choke lever (Fig. 2/Item 17) to I I.
5. Actuate the decompression lever (Fig. 42/
Item 33).
6. Hold the equipment fi rmly and pull out the
starter cable (Fig. 2/Item 14) until you feel it
begin to resist. Then tug sharply on the starter
cable 2 times.
7. Set the choke lever (Fig. 2/Item 17) to I I.
8. Hold the equipment fi rmly and pull out the
starter cable (Fig. 2/Item 14) until you feel it
begin to resist. Then tug sharply on the starter
cable 4 times. The equipment should start.
Important: Never allow the starter line to snap
back. This may result in damage.
Once the engine has started, allow the equip-
ment to warm up for 10 seconds.
Important: Since the choke lever is secured,
the cutting tool starts to operate when the
engine is started.
Then release the choke lever by actuating the
throttle lever once.
9. If the engine does not start up, repeat steps
4-9 above.
Please note: If the engine does not start up even
after several attempts, read the section „Engine
troubleshooting".
Please note: Always pull the starter cord out in
a straight line. If it is pulled out at an angle, then
friction will occur on the eyelet. As a result of this
friction, the cable will become frayed and will
wear away faster. Always hold the starter handle
when the cable retracts.
Never allow the cable to snap back when it has
been pulled out.
07.08.2017 09:00:42
07.08.2017 09:00:42

Publicidad

loading