Nolan N903 Seguridad E Instrucciones página 8

N90-3
DUAL ACTION
This unique chin guard opening system - positioned in the centre of the chin guard - al-
lows for easy, one-handed opening and prevents it from accidentally opening. The chin
guard can only be opened after operating the first red lever (release lever) and then the
second red lever (opening lever).
The configuration with chin guard open and VPS raised is recommended to ensure
a better fit of the helmet.
1 CHIN GUARD OPENING
1.1 Push the red release lever outwards by turning it with your thumb (Fig.1).
1.2 Place your forefinger on top of the opening lever and push it downwards to lock
the chin guard (Fig.2).
1.3 Pull the chin guard forwards and then follow its rotation upwards (Fig.3).
If the helmet is used with chin guard open (J configuration), it is recommended
that you place the left side locking slider in position "J" to secure the chin guard
in lifted position (Fig.4B).
2 CHIN GUARD CLOSING
WARNING
When the left side locking slider is in position "J" do not force the closing of the
chin guard because it could damage the helmet's closing mechanism. Move the
locking slider to position "P" (Fig.4A) to close the chin guard.
2.1 Pull the chin guard downwards, following its rotation, until you hear the closing
mechanism clicking (Fig.3).
2.2 Make sure the chin guard is correctly fastened by pulling it forwards and by check-
ing that both sides remain fastened to the shell.
When the left side locking slider is in position "P", the chin guard can be
opened and/or closed (Fig.4A).
When the left side locking slider is in position "J", the chin guard cannot be closed and
remains blocked in open position (Fig.4B).
WARNING
- The protection level of this helmet whilst riding depends on the configuration
adopted by the user: total protection if the chin guard and visor are closed,
partial protection if the chin guard and/or visor are open.
- Do not remove nor tamper with the fixing screws that connect the chin guard to
the shell.
- Do not use the helmet without chin guard.
- Never use the helmet in case of malfunctioning and/or damages of the chin guard
opening system. In case of doubts regarding the correct operation of the chin
guard opening mechanism, contact a Nolangroup authorized dealer.
VISOR (NMS-04)
1 DISASSEMBLY
1.1 Close the chin guard (if open) and open the visor completely.
14
INSTRUCTIONS FOR USE
1.2 Press the left side part of the visor towards the helmet, as shown in Fig.5, and simul-
taneously press the mechanism release lever by pressing it downwards (Fig.6), until
the rear grip pawl D1 of the visor comes out from the relevant seat of the mechanism.
1.3 Release the mechanism release lever and pull the visor towards the outside of the
helmet so that the two pawls (D1 and D2) and the front hooking pin (D3) come out
from the mechanism (Fig.7)
1.4 Release the visor and make it slide upwards to release it completely from the
mechanism.
1.5 Follow the same steps on the other side of the helmet.
2 ASSEMBLY
2.1 Close the chin guard (if open) and set the visor in open position by placing the
pawls (D1 and D2) and the front pin D3 in line with the relevant seats on the visor
mechanism (Fig.7).
2.2 Insert the front pin D3 into the relevant seat and press the visor against the mech-
anism in line with pawl D2.
2.3 Simultaneously move the visor downwards until the rear pawl D1 is fastened under
the mechanism lever.
2.4 Follow the same steps on the other side of the helmet.
2.5 Close the visor completely.
WARNING
- Make sure that the mechanisms are working properly. Open the visor. By lifting the
chin guard, the visor closes automatically. If necessary, repeat the same opera-
tions mentioned above.
- Make sure that the mechanisms are working properly. Open and close the visor,
making sure the latter is held in place in its different positions by the mechanisms
itself. If necessary, repeat the same operations mentioned above.
- Do not use the helmet if the visor has not been assembled properly.
- Do not remove the side mechanisms from the chin guard.
- Should any of the side mechanisms fail or be damaged, please contact a Nolan-
group authorized dealer.
MINIMUM OPENING POSITION WITH DEFOGGING FUNCTION
The visor can be slightly opened, with no need to place it on the first notch of the mech-
anism. In this configuration, the inner central pawl of the visor leans onto a specific
seat on the helmet chin guard that allows the visor to be kept in a minimum opening
position for a better ventilation and making defogging easier, especially at low speed
or during short stops.
( NMS-04 )
(Available as standard or accessory/spare part)
1 ASSEMBLY
1.1 Disassemble the visor (see instructions above).
1.2 Check that the inner surface of the visor is clean and that the pin adjustment ex-
ternal levers are turned inwards (Fig.8).
N90-3
15
INSTRUCTIONS FOR USE