Publicidad
Idiomas disponibles
Idiomas disponibles
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
•
Combined switch for on/off and speed control A 7
- control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger A 8
•
Charging battery
! read the safety warnings and instructions
provided with the charger
•
Removing/installing the battery 2
•
Attaching belt clip 9
- attach the belt clip F to the drill with the supplied screw.
•
Battery level indicator q
- press the battery level indicator button G to show the
current battery level q a
! when the lowest level of the battery indicator
starts flashing after pressing button G q b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button G q c, the battery is not
within the allowable operating temperature range
•
LED-light F r
LED-light automatically lights on when activating the on/
off switch
! when LED-light starts flashing, the battery
protection is activated (see below)
•
Battery protection
The tool is suddenly being switched off or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing button G q c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level q b is shown by the battery level indicator
when pressing button G; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
Changing direction of rotation w
•
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
•
Changing bits e
- to remove a bit, pull the locking sleeve C forward 2
- pull the locking sleeve C forward, insert the bit to the
stop into the bit holder and release the locking sleeve C
to lock the bit. e a e b e c
! only use bits with ball catch, other bits can be
used with a universal bit holder with ball catch e b
! do not use bits with a damaged shank
•
Holding and guiding the tool t
! while working, always hold the tool at the grey-
coloured grip area(s)
- keep ventilation slots D 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
•
Use the appropriate bits
When turning in a screw at/near the cross cut end or an
•
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
•
For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
•
When screwdriving in hard wood one should pre-drill a
hole
For more information see www.skil.com
•
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
•
Always keep tool clean (especially ventilation slots D 2 )
! remove battery from tool before cleaning
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
•
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
•
Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
•
Measured in accordance with EN 62841 the sound
pressure level of this tool is 83.7 dB(A) and the sound
power level 94.7 dB(A) (uncertainty K = 3 dB), and
the vibration 5.68 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
•
The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
9
patterns
Publicidad
