Publicidad
Enlaces rápidos
U P
®
C
®
ASME A112.18.1 / CSA B125.1
ICC/ANSI A117.1
Models/Modelos/Modèles
6390 & 6395
Series/Series/Seria
RSVP™
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:
Note: A small packet of silicone grease has been included with your faucet. You may use it to lubricate O-rings when necessary.
Nota: Con su llave de agua se incluye un sobrecito de grasa de silicón. Cuando sea necesario, puede utilizarlo para lubricar los aros-O.
Note : Un petit contenant de graisse à la silicone est inclus avec votre robinet. Vous pouvez l'utiliser pour lubrifier les joints toriques au besoin.
For easy installation of your
Brizo
faucet you will need:
®
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care, and maintenance
information.
• To purchase the correct water supply hook-up.
Para instalación fácil de su llave
Brizo
usted necesitará:
®
• LEER TODAS las instrucciones completamente
antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
• Comprar las conexiones correctas para el
suministro de agua.
Pour installer votre robinet
Brizo
®
facilement, vous devez:
• LIRE TOUTES les instructions avant
de débuter;
• LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
• Acheter le bon nécessaire de raccordement.
TWO HANDLE WIDESPREAD BIDET FAUCETS
WITH INTEGRAL VACUUM BREAKER
LLAVES DE AGUA DE PIEZAS SEPARADAS, DE
DOS MANIJAS, PARA BIDETS CON EL TRITURADOR
INTEGRAL DEL VACÍO
ROBINETS À GRAND ENTRAXE ET À DEUX MANETTES
POUR BIDET AVEC LE BRISEUR INTÉGRAL DE VIDE
6390
1
6395
L
L
9/26/09
2 mm
Rev. E
12078.00
Publicidad
Manuales relacionados para Brizo RSVP 6390
Resumen de contenidos para Brizo RSVP 6390
- Página 1 Note : Un petit contenant de graisse à la silicone est inclus avec votre robinet. Vous pouvez l’utiliser pour lubrifier les joints toriques au besoin. For easy installation of your 2 mm Brizo faucet you will need: ® • To READ ALL the instructions completely before beginning.
- Página 2 This warranty excludes all industrial, commercial & business usage, whose purchasers are parts may be obtained by calling 1-877-345-BRIZO (2749) (in the U.S. and Canada) or by hereby extended a five year limited warranty from the date of purchase, with all other terms of writing to: this warranty applying except the duration of the warranty.
- Página 3 3 mm OPERATING INSTRUCTIONS MAINTENANCE A. Check to be sure diverter valve handle (1) is in the rim feed position SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE ASSEMBLIES. (turned fully clockwise). If your bidet faucet leaks out of rim feed area, or from rosette sprayer, or B.
- Página 4 Modelos / Modèles 6390 & 6395 Models / RP48417▲ Cross Handle & Body Manija en Cruz y RP48447▲ Cuerpo Diverter Handle & Manette cruciforme RP46407▲ Set Screw et corps de manette Lever Handle & Body, Hot Side Manija Desviadora y Palanca y Cuerpo, Lado Caliente RP48448▲...
- Página 5 2 mm INSTALLATION OF DIVERTER VALVE/VACUUM BREAKER Note: Please refer to bidet bowl installation instructions to identify hole location for diverter valve. INSTALLATION OF ROSETTE SPRAY Hole size must be 1-1/8” diameter minimum. Apply silicone bead (1) under rosette (2). Insert Connect diverter valve (1) with “Y”...
- Página 6 INSTALLATION OF VALVE ASSEMBLIES & TRIM Note: Holes for valves must be 1-1/8" diameter minimum and must be at least 5" apart. If handles do not align, unscrew one or both handle & body assemblies and try Look for a blue label or dot on cold valve assembly and red label or dot on hot valve assembling again after rotating handle slightly forward or backward until assembly and install them on appropriate side.
- Página 7 1/2" (12.7 mm) MAKE CONNECTIONS TO WATER LINES: POP-UP INSTALLATION Push black gasket (1), cone side up, and fiber washer Choose hook-ups for 1/2" I.P.S. connections: Remove plastic stopper cap (1) and stopper (2) (2) onto flange (3) from under bidet. Screw nut (4) onto (1) Ball nose riser (3/8"...
- Página 8 Insert pivot rod (1) into body (2). Tighten pivot nut (3). FLUSH YOUR SYSTEM Turn diverter handle (1) clockwise to ‘rim feed’ position. Turn on water Make sure gasket (1) is in place under lift rod guide base (2). Insert lift rod guide assembly into appropriate hole in bowl deck.